Clik here to view.
Why my PC can not recognize the agilent DSO5012A by the GPIB-USB-HS？
1. I have installed the NI-488.2 driver，and the agilent E3631A can be recognized by the GPIB-USB-HS2.I have selected all list passports include NiVisaTulip. dll，but there is no use. 3. I have replaced...
View ArticleネットワークにつながっていないPCにNI-VISA、NI-DAQ、NI-4882のドライバをインストールしたい
Window10 64bitネットワークに接続していないPCにNI-VISA、NI-DAQ、NI-4882をインストールする必要があります。別のネットワークに接続可能なPCに、最新ドライバをダウンロードし、USBにおとしました。 ネットワークに接続していないPCに、USB経由でドライバをインストールしようとしましたが、「NIパッケージマネージャ 更新できなかったファイルがあります。...
View ArticleAbnormal shutdown：VI_ERROR_CONN_LOST(-1073807194)
HI:When the device is shut down abnormally, connect VI and an error of "the IO connection for the session has been lost" will be reported. The solution I found on the forum is to turn off VI and then...
View ArticleWhere can I find the "TI TMS9914A GPIB Controller Manual" or controller...
Hello, I want to design a GPIB interface card using NAT9914(as controller),Where can I find the "TI TMS9914A GPIB Controller Manual" or controller manual for NAT9914? thanks. Best regards!
View ArticleGPIB analyzer Interface not found error
Hi, I want to use Labview with SR830 with GPIB(National istrument). Software installed but when i started the GPIB Analyzer it gave the error of Interface was not found. Please note: GPIB-USB-HS is in...
View ArticleProblem with running Hantek 6022BE driver/HTMarch.dll in macOS catalina
Hi there I would like to use Hantek 6022BE driver in Labview 2018 running on macOS. I have a problem with recognizing HTMarch.dll. It seems there is a mismatch between 64 bit labview and 32 bit...
View ArticleClik here to view.
Linked VISA library with Code Block IDE
Hi all,I face a problem to execute this code in Code block IDE. I am not sure the right linker and compiler setup.This is my compiler and liner setup: When I try to build and run this code:This is the...
View Articleserial communication visa read
When I read the visa in serial communication, the data comes in and the data is broken in the middle. Is this because of the difference in communication speed?There was a delay before reading the...
View ArticleEurotherm 3500 control using Labview
Hi,I need some help regarding the Eurotherm 3500 series communication, I am using 3500 series for controlling a fan and a feedback from a mass-flow sensor, with labview on a computer, how should I set...
View ArticleEnd of support GPIB-ENET/1000
Hello,I would like to know if there is a forecast date for the end of support/end of sale for the equipment GPIB-ENET/1000 or maybe at the opposite an engagment of NI to support it upto some date...
View ArticleMassive MIMO Testbed
We have a MIMO testbed includes PXIe8840, three PXIe 8384, two NI FlexRIO, NI PXIe 6674T, and 24 USRPs. Our goal is to split this into three exact testbeds. How it could be done? what extra hardwares...
View ArticleGPIB/ENET100 fails 01-02-2020.
FYI, I have three of these devices in critical roles, and all three failed within seconds of each other on the 2nd of this month. A reset/reboot restored functionality, but long-term stability is unknown.
View ArticlePXI-5114 Programmable Function Interface (PFI 0 and PFI 1)
Using a PXI-5114 scope and looking for information on configuring the 9 pin AUX I/O front panel connector Programmable Function Interface (PFI 0 and PFI 1) . I can't seem to find it in the documents....
View ArticleError Code 0xBFFF0011 when trying to set up VISA on NI MAX for Keithley 2701
I have been trying to set up my Keithley 2701. I have been trying to follow the instructions from other posts, as follows1) Open NI MAX2) Right click devices and interfaces and click "Create new"3)...
View ArticleUSB 4000 from ocean optics not recognized
Hi everyone,I'm using the USB4000 for a university project and hadn't had any problems connecting it up to my old computers however I had to change the computer I was working with and haven't gotten...
View ArticleClik here to view.
NI VISA connection error
Hello. I have some problem of connection VISA instrument. I want to controller my linear stage using RS232 to USB connection cable. Actually, I used this instrument before, but now there is connection...
View ArticleDriver for Keysight PA2203A
Hey, I need to acquire and plot the voltage and current waveforms from Keysight PA2203A. But the driver I am getting can do only the Harmonic, power system measurements. I have seen the exact drivers...
View ArticleControlling a programmable DC power supply via LabVIEW
HiI am looking to control a programmable DC power supply (Model: PTDP-5-5R-BI, make: Power TM), which is input into a pair of electromagnets to generate a magnetic field. I could search for the...
View ArticleClik here to view.
8164B instrumentID could not be queried with driver subVI
Hello all,i have an Agilent 8164B connected over Lan, if i try VISA commands in Labview everything works fine. But if I want to use the subVIs from the driver it didnt work. If I use Initialize.vi i...
View Article