Generic I/O Error: 6
Hi,I Have a kiethley SMU-2410C instrument. Labview is acting as software to carry the Current Vs Voltage studies. The program is giving error 6 : Generic I/O error, when we run the program. Please go...
View ArticleVDS Vosskühler CCD-4000 with framegrabber NI PCI 1422
Dear community, I am trying to use an old camera (VDS Vosskühler CCD-4000) with an old framegrabber (NI PCI 1422).Installing Vision Acquisition Software version 18.0 (...
View ArticleAvailable version of NI-VISA for Debian Linux ?
Hi everybody, I just bought a device that I'd want to contol using VISA under linux but I cannot find any available version for my Operating System (Debian 8.3 - 64 bit). Is there any (even...
View Articleausbtmc.sys Fails Windows 10 Driver Verification?
I was chasing down a BSoD, and ran across this error while running the Win10 Driver Verifier. The Stop Code is DRIVER VERIFIER DETECTED VIOLATION. Same behavior after installing VISA 17.5, 19.0 and...
View ArticleLabview Drivers for Neslab chillers, Agilent 34970A, and Digikrom Monochromator
I know it's been a long time since anybody inquired about this, but a few months ago I rewrote the Neslab drivers that were available from the Instrument Driver Network for 10+ years, and in my...
View ArticleVisa Session Access Using LW-CVI
Good Morning. I am developing a system where I would like, on start up, to initialise and open sessions to all the instrumentation. I would like to store the Visa Session handles so I can access the...
View ArticleNGA 2000 ANALYSER
Hello Siri am Amr Awad associate Prof. Mansoura Universityi am intended to purchase USB 6008 or 6009 (Data collection)but i have some questions regarding the Cardit will work with NGA 2000 Analyser...
View ArticleNI SessionManager
Hi, I'm trying to get my head around NI Session Manager. To start, I looked at the .ini file. The comments suggest that this file is automatically generated by session manager. I'm a bit lost as to...
View ArticleNew guy here with HP8566 and GPIB-USB-HS
Hi all - I'm new to NI and GPIB to USB adapters. I have the GPIB-USB-US from NI and an old HP8566 spectrum analyzer. I also have Measurement and automation explorer installed on my PC, and I'm trying...
View ArticleAny setting require for GPIB Box to support 115200kb/s
Hi,NI GPIB RS232 - GPIB Serial Port Controller/ConverterIs there any setting is required in order for this GPIB box to support 115200 kb/s?If there is a need, where have show the procedures?Thanks! Toh
View ArticleRead Thorlabs optical power meter in LabVIEW 2018 via USB connection
Hello all, I have been trying to read data from Thorlabs PM101R optical power meter using Labview 2018 (32 bit). Everything was fine. But suddenly I get an error as - Possible reason(s):"VISA: (Hex...
View ArticleSPI Listen only from a MiniQUSB
Hi, Im kinda new to the SPI. Currently I having an NI-8451 to be use to control an EVKIT. But notice that NI-MAX don't have an app use for SPI to "Listen only" as compare to normal CAN. I try out on...
View ArticleHiac/Royco 5230 counter
Hi. i have a hiace/royco 5230 particle counter and Missing user manual. if you have this user manual, please send to me. heydarfathollahi198@gmail.com Best Regard
View ArticleNI Instrument driver finder cannot discover the connected instrument
I am trying to search for an instrument driver for the NI9237 module, which is connected to my PC (Windows 10) where LabVIEW 2015 is installed through USB 2.0 (provided by NI while purchasing) via cDAQ...
View ArticleRandom Serial Communication Error
I am currently trying to program a PCB. This works by sending serial commands to the board at 115200 baud rate. Currently, the VI works most of the time but after a couple hundred loops, the board will...
View ArticleClik here to view.
VISA error 1073807263
I am trying to use the latest Agilent 33210a instrument driver (2018) on labview 2019 to write SCPI commands through the GPIB port to a the waveform generator in order to output a triangle wave. I...
View ArticleReading battery voltage using the 10 bit ADC via SPI on MyRIO-1900
Hi there,I am trying to read a battery voltage (3.39 V) using 10bit-ADC (MCP3002 with SPI) by MyRIO 1900. I think I have connected everything correctly (plz see the attached). However, the output value...
View Articleissue connecting to both a network device and a remote system device
I currently use LabVIEW 2016 to connect to an FPGA/PXI chassis. In NI-MAX it is listed under "remote systems." I have one vi which programs the FPGA, and then a host program which calls that using an...
View ArticleMy myRio losses connection when connecting to a VPN
So i'm able to connect to my myRio when on my own network. When I go on my schools VPN the connection is lost. Anyone who might know how to solve this problem?
View ArticleIgus Dryve D1 controller in labview
Hello, l am a student working on my thesis project which is to control linear actuator with LabVIEW programming. l want to write code to control Igus Dryve D1 motor controller in LabVIEW by TC/IP. l...
View Article