Problem controlling Yokogawa AQ6370C by TekVISA and RS-232 (Visual Studio C#)
I have OSA Yokogawa AQ6370C connected via RS-232. When I use direct connection to com port - all work fine!I send command "*IDN?\r\n" an recieve correct answer "YOKOGAWA,AQ6370C,91L412833,01.02". Now i...
View ArticleClik here to view.
I want to receive HEX data by VISA. What am I supposed to do??
<Pic. 1> <Pic.1> is HEX Data received by CodeVisionAVR. Actually, The Data is from AHRS. ( I'm making some kind of Ground Control System, so I need Euler angle data.) But, in LabView...
View ArticleMake an ACPR measurement (set up for 5 MHz and 10 MHz offsets) using Agilent...
We are using an Agilent VSA E4406A. We would like to measure Adjacent Channel Power Ratio & am trying to use the Agilent PSA (W-CDMA) Series drivers. So the ACPR, it is set up for 5 MHz and 10 MHz...
View ArticleLabVIEW control Interface 54645d, Please Help!!!
Hi, I am having trouble getting two trace signals or to at least get signal from channel 2 on my labview interface, I get the two signal traces on the physical oscilloscope and when I try and execute...
View Articleburkert valve equivalent
Hello. Does anyone know about the equivalent valves for the following burkert valves which could be less expensiveType 6519 H standard: 132465 Type 5420 : 456954Thanks
View Articleserial communication
Hello, I'm Shrinivas Pathak. I'm new to LabVIEW... I've been given a task to send some commands such as ''start motor'', ''stop motor'' etc... i have to send these set of commands through...
View ArticleRead Real Time data From VISA and plot on graph
Hello. I have a hardware which contonuously sends Sine wave data seperated by character (*)e.g. -0.9999*0.0000*-1.0000 etc. (attacheed Hyperterminal snap).. The Sine wave has sampling rate 16 kHz. I...
View Articleprofibus and IFM-controller
We have a new fermenter with profibus port.it's has an USB-RS485 converter(PC) cable.I want to edit a subvi in labview 2012.where can I find the driver or examples?
View Articleincremented voltage output using DAQPad-6259
Hello, I'm really new to Labview and trying to make a program that increases the output voltage overtime using my DAQPad-6259. Basically I want to start from a certain voltage and then given a specific...
View ArticleCommunication between two programs using shared NI-GPIB
Hello to everybody! We are buying a PC-based device having an NI-GPIB board used by the software to communicate with the external world. Normally I'm expected to use the following architecture: PC With...
View ArticleHow to apply linear equation on real time graph
I am working on my trainer which shows the strength of signal on 7 segment display. I have made my own harwdare that takes the values from hardware and these values are shown in waform chart in labview...
View ArticleLabVIEW will not recognize physical channel in DAQ assisstant when MAX shows...
Ni cDAQ-9184 is connected to laptop with ethernet cable. System state says running and a NI 9481 module is in slot 1. However, when I try to add device, I get error 201401. I am trying to get the DAQ...
View ArticleNI488.2 linux installation problem
Hi, I am using Scientific Linux 6.5 32bit and I try to install NI-488.2 to talk with NI PCI-GPIB. I downloaded http://www.ni.com/download/ni-488.2-2.9.1/3186/en/ and followed the installation...
View ArticleWhy it's take a while to get a TCP Connection
I GuysI open VISA Interactive Controland I see my USB Connection just in time,but the TCP/IP Connection takes at least 5 min to be recognized.What is the reason for this and can I force the auto...
View ArticleInitialize Visa Agilent N57
I am trying to initialize a session to an Agilent N5764A. I keep getting an error code -1074001254 saying N5700 Write to Instrument -> ConfigVoltage Limit.vi -> N5700 Getting Strarted.vi...
View Articlelabtop and desktop
I use GPIB USB HS controller. When I connect it to my labtop an run MAX I can see the keithley connected to the controller, but when I connect the same controller with the same instrument on the...
View Articleke485
I am tring to use the example in ke485 driver to control keithley 6487 picommeter using LabViwe 2013. the installation was O.K. and MAX detect the instrument but when I run the example no errors show...
View ArticleControl servo motor festo por ethernet
Hola a todos, hace tiempo trabajé con labview y ahora me han vuelto a mandar otro trabajito, la verdad es que me gustaría saber si labview ha realizado una api para los servo-motores de fetos que van...
View ArticleKepco SNR 488-8 Too Many listners on GPIB
Hello, I am having problems connecting to a Kepco SNR 488-8 Power Controller via the GPIB bus. The odd thing is that I was able to connect to it before... Here are the steps to reproduce the...
View ArticleSick LMS 2xx Series angular resolution
HiThere is some problems i meet ,Lms is a laser measurement that i want to change the regular resolution from 1°/ 180° to 0.5°/180°.I have tried use the NI program to solve this problem but it seems...
View Article