USBTMC Missing Drivers
I am attempting to connect and install a USBTMC-compatible device (a BK Precision 9115) to a work PC which sits on a network with no internet access. According to both the Readme on BK Precision's...
View Article488.2 ver 20.0
After installing the driver, there is a help file named "NI-488.2.NET Framework 4.0 Help", it can't be opened with Help-Viewer.How to open the file and read it ?
View ArticleClik here to view.
Trace Measurement of Keysight U2044XA - Input Protocol Error
Hi NI Community, Hoping you guys can help me out. I downloaded the Agilent U2000A Series Sensor driver off the NI website. My goal is to do a trace measurement so I can view a pulsed RF signal over...
View ArticleSave data in milliseconds
I save analog signals in real time but I only manage to save them every second, but I need to save the data in milliseconds. How can I save them in
View Articlelibnipalu.so failed to initialize
centos 7 64bit， first， use ./INSTALL to install lv2017pro-linux, then use ./INSTALL to install NI-VISA-17.0.0 ， when run visa function in labview , tips " libnipalu.so failed to initialize Perhaps you...
View ArticleCommunication Fails between DAQ970A and PC through LAN
Hi,I am trying to establish the connection between DAQ970A and PC(LabVIEW 2017) through LAN facility. Using Instruments IP address and port number, same thing has been configured in NI Max-Network...
View ArticleGPIB ENET/100 with calibration executive
Hi all, CONDITIONI have to setup the calibration executive 6.0 on a computer which is connected to a GPIB ENET/100.The last NI-488.2 drivers compatible with GPIB ENET/100 is the version 17.6 which I...
View ArticleDriver for GPIB-USB-A adapter
Hi, I need a driver for a GPIB-USB-A adapter in order for my computer to recognize my keithley sourcemeter. Could you please help me resolve this issue? NI Hardware: GPIB-USB-AOperating System: Windows...
View ArticleClik here to view.
Agilent/Keysight 4155A parameter analyzer continuous sampling mode
Hi everyone! I am working on a project that extracts data from the Agilent/Keysight 4155A (semiconductor parameter analyzer). Earlier, I was running a data extraction after I got data on my instrument...
View ArticleInstrument found in scan but does not respond in NI 488.2 communicator
Hello everyone, I am trying to communicate with a data precision 8200. The commands are very simple...
View ArticleRS232 Alicat and Labview communication drop
At the moment I have a problem I cannot pin down. Seemingly at random my communication with my RS232 Alicat Device will get held up. It will get held up somewhere in the read or write process and be...
View ArticleConnection Lost - Windows 10 - Dell Optiplex 3060 Micro
I'm facing a connection lost issue while acquiring data from a Yokogawa DA100 old hardware. This same application was working fine with the previous PC (Windows 7), but recently the company migrate all...
View ArticleGetting an output for each new measurment from Keithley 2400
Hi everyone, I am working on a project where I am using a Keithley 2400 Sourcemeter (GPIB HS USB connection) to measure surface conductivity of a specific material. I have a fixed delay number (say...
View ArticleKeithley 2700 fast measurement of voltage waveform
I am interfacing LabVIEW 2018 using GPIB with a Keithley 2700 with no internal mux cards--so I want to read straight from the banana plug inputs on the panel front in 2 wire mode. The Keithley 2700...
View ArticleKeithley 2000 Read Single.vi
anyone know where I can find this .vi sample? I just purchased a refurbished 2000 unit. Thanks in advance.
View ArticleKeysight 34972A looses USB connection in LabVIEW
Hi,I am controlling a Keysight 34972A data logger and switch with LabVIEW and via an USB connection. Everything seems to work fine for most of the time, but at random intervals, the connection to the...
View ArticleNI-VISA on SBC with GPIO
OK, I've done all my due diligence and can't find any help on this. Sorry if it's a known topic. I can't connect directly to the target instrument with Ethernet, so I want to buffer data remotely...
View ArticleGPIB-ENET/1000 Reset and could not be found
Hi, I have an GPIB Enet 1000 configured to a static IP address. But I could no longer see it on NI MAX. I tried to reset the device following those steps on the manual"Turn off the device.Hold down the...
View ArticleClik here to view.
Unknown code error in Python using NI GPIB-USB-HS
Hi, I am using NI GPIB-USB-HS device to control Keithley 2700, Chroma load and Agilent DC power supply. I have all the devices connected and I can see it as the GPIB devices in Python.But when I tried...
View ArticleGPIB-ENET/100 ON WINDOWS 10
Is there any way to use my GPIB-ENET/100 on Windows 10? Recently upgraded (by force) to Win10. I have NI MAX installed with NI-488.20 and the GPIB Wizard only shows adding a ENET/1000. I've tried to...
View Article