使用ADLINK PCIe-RTV24影像擷取卡所提供的VI
請問一下，我使用ADLINK PCIe-RTV24影像擷取卡所提供的VI時，出現了error該怎麼解決，另外就是有其他方法能夠利用LabVIEW來得到擷取卡的影像呢?
View ArticleControl SR245 to scan input ports via RS232
Hi guys, SR245 is said to have the ability to independently read the input ports (i.e., 1 and 2) and store a series of data point using scan command (see manual page 44), which can acquire data up to...
View ArticleHow to get a quote / Order of GPIB-USB-HS+ for EGYPT considering that Online...
I tried this process online, but it ask me to FAX it to +961 1-334 300UAE FAX no is terminated as will as NI Phone No. in Egypt 0112190002 /0112190003 Please advice how to get this quote?ThanksSami...
View Articlekeithley 4200 drivers
helloi have just connected my keithley 4200 via GPIB cable and I'm getting this message:windows does not have a driver associated with your device.any driver that i could use please help
View ArticleClik here to view.
Modbus for temperature controller
Dear all,I am new with Labview, hence, my apologies for any stupid questions. I have a temperature controoler Ascon KX03 that can communicate trhough a serial port with Modbus protocol (I attached the...
View ArticleFailing DMM self-test with -223911
When I run self-test (in NI MAX) for my PXI-4605, I get a -223911 error. The documentation states that this is a naming issue. I tried the rename it, save, rename again, save trick. Didn't work....
View ArticlecRIO, PSUs, MFCs connected via Ethernet
Hi, I am trying to use Labview to control and save data from several power supply units (PSUs) and mass flow controllers (MFCs).In particular, I am using a cRIO 9031, an Ethernet switch (TP-link),...
View ArticleProgrammable Temp/RH Sensor
This is silly problem to have, but apparently it is a problem. I need, for a medical device manufacturing application: a programmable, calibrate-able temperature + relative humidity meter. I can't...
View ArticleVOLTAGE MEASUREMENT IN MS WITH KEITHLEY 2182A INSTRUMENT
hello everyone ,i have i probleme i can measure the voltage white KEITHLEY 2182A INSTRUMENT in ms , i have a current pulse width 10 ms and i want mesure the voltage,i made connection gpib with...
View ArticleClik here to view.
Instrument not found
Hi! I have an MKS 946 Vacuum System Controller, and I have LABVIEW 20.0.0in my computer. I have connected the device via serial port, I have installed the NI-serial driver. Still I cannot find the...
View ArticleNI-488.2 old driver for window7
Does anyone know where I can get NI-488.2 old drivers for window 7? It's supposed to be NI-488.2 2.8,3.0, or 3.1... I will appreciate if anyone can share a link for download! Thank you!
View ArticleSerial-Data LVDT
Hello, I have a LVDT connected to my COM1 serial port. This gives me around 7000 readings when I read the COM Port. It outputs a string like "N +0.642...." to signify the flatness of a section. The...
View ArticleWhether the analog output can generate PWM waves
Whether the analog output can generate PWM waves by generate a square wave
View ArticleClik here to view.
Problem reading SCPI SYST:ERR? for Keysight 34465A
I wrote a Labview app for a Keithley 34465A multimeter to be able to measure the current of a short biphasic current pulse. Initially I started with the NI drivers that are available, but they did not...
View ArticleSerial Data - String
Hello, I have a LVDT connected to my COM1 serial port. This gives me around 7000 readings when I read the COM Port. It outputs a string like "N +0.642...." to signify the flatness of a section. The...
View ArticleNewbie gpib question
I hope this is not too stupid a question, but I want to start as simple as possible. I control other (i.e., Tek, HP) GPIB-enabled instruments using a Prologix usb-to-GPIBdongle and send ***simple ascii...
View ArticleUsing a lantronix uds2100 to read out a Granville-Philips 350 Gauge Controller
Hello,I hope I choose the right board for my problem. I try to read out the pressure of a vacuum which will messure by a Granville-Philips 350 Gauge Controller. As an Adapter (serial to ethernet) I...
View ArticleNI-VISA仪器操作时超时
My instrument is Aglient 8153A, and the driver, VISA driver, and NI-488.2 have been installed. When I test the instrument on the instrument test panel in NI MAX, the address of the instrument can be...
View ArticleNi8452 I2CSlave doesn't react to RepeatedStart after master reads data from...
Hi All, I am Using the Ni8452 with the C-Api in order to emulate an i2c-slave device (For now this is an EEProm). Currently I am facing the issue that the NI-8452 Slave stops working correctly after i...
View Article