NI 488 PCI settings
I am having issues with moving my NI488 PCI to a win 10 comp. I downloaded and installed the 2.7.3.49152 drivers. It looks good in DEVMAN but in Measurement and automation explorere it cannot find a...
View ArticleClik here to view.
USB-8451 SMBus communication
Hi, I want to use the USB-8451 interface to communicate with a SMBus. For the USB-8451 there are no problems reported in the Windows Device Manager or in the Measurement & Automation Explorer....
View ArticleSerial communication with a titrator
Hello all, I will have a serially connected titrator (USB connected, not automatic) comprised of a burette, mixer and a potentiometer. I have been given a set of commands (ASCII format, eg. B for...
View ArticleCommunication problems after upgrading to NI-488.2 v19.5
I have an application that has been in use for several years. The program communicates with a Keithley 7002 scanner and 6485 picoammeter to read currents from several channels. I recently upgraded NI...
View ArticleKeithley 6485 ID Query failed
Hey folks,I have connected several instruments via a Keithley KUSB488B to my computer. The voltage source (Keithley 2410) works fine and there are no correction errors. But I have problems while...
View ArticleNIMax unable to start correctly (0xc000007b) - Application Error
I had the NIMax running fine and then I had to install software for R&S CMW100. During that installation, I had to uninstall/reinstall Microsoft Visual C++ Redistributable to get it going. After...
View Article"Box" available to control LAN instrument via CAN bus ?
Hello,did someone ever hear of a solution to control a lan instrumet via can bus?INSTR <-> lanport_out <-> lanport_in <-> [blackbox] <-> canport_out <-> canport_in...
View ArticleInterfacing LabVIEW with Yokogawa UT32A Controller
Hello Guys! I usually use Yokogawa UT32A controller for process control applications.I would like to read/write the sensor values from UT32A via Modbus protocol (I also have a modbus to serial...
View ArticleRFID read module to interface with labview getting error 56 need support
Hi Team,iam trying to interface a RFID device with labview which reads the tags within 150 meters continuously .its working with the Vendor application please find the attachment of the reading. need...
View Articlers232 cable set up
hi, I am very new to LabView and very bad at it. Long story short I am trying to connect a pump to labview via a RS232 cable so i can create a basic control of the pump. However, I am running into...
View ArticleSDG6022X DATA format
Hello,i need help with following task. Im programing arbitrary waveform generator sdg6022x using MATLAB, and i cannot figure out how to format data so the device understand them correctly. Manufacturer...
View ArticleHow to install PCI-GPIB
Hi How do I install NI PCI-GPIB in Win10?I have try 19.5 & 17.5, but still not success. BR
View Articleunable to find an entry point named"xxx" in dll "visa32.dll"
Hi：I've tried to install the Ni driver and the keysight driver. All report this error.But there is no such problem on other computers.I tried to re register the DLL, but it didn't work.thanks
View ArticleTemperature stabilization during ramping with TIC500 Cryovac by LABVIEW...
Dear all, I am trying to write a LabVIEW program to stabilize the temperature during ramping with TIC500 Cryovac. This means that I want to read the temperature while it is stabilized. Does anyone have...
View ArticleVISA Serial Communication With Micro Ellipse INS
I am trying to communicate with the ellipse Micro AHRS & INS. I have configured the VISA serial port and have attached the VI. I have also attached what I am trying to read and the command i am...
View Articlecontrolling the data flow and the timining between the sequences
Dear All, I have a setup that involves a power supply (HP 6632B), a thermistor that I can read the resistance through a HP 3478, a Newport 2835 (dual channel, bot channel readings taken). I wrote a vi,...
View ArticleEllipse 2 Micro Binary Logs 'availability'
I am trying to use labview to communicate with the ellipse 2 micro AHRS & INS. Just get basic information, like time, velocity, acceleration etc. However I am dealing with an ELLIPSE2-I-G4A3-M1, it...
View ArticleAlternating volatage and current values through Electrometer 6517A using labview
I am using Keithley Electrometer 6517A for measuring alternating voltage, current and charge values of my triboelectric nanogenerator using NI Labview. Can any one help me out to guide me how to do it?
View ArticleC++ driver call to check Ni Switch topology
There doesn't seem to be any c++ driver call for checking the current configured topology on the ni switch. Does anyone know if one exists?
View ArticleCannot open multiple VISA/VXI sessions on instrument AC POWER Asterion
Hello, I have an issue when I try to open multiple communicating sessions between my controller and Asterion AC power model AST2253.To establish the initial communication I use NI VISA toolset 5.6.0...
View Article