Read real time (pressure) data from CPC6000 and plot on graph using GPIB
Hi, I'm trying to read real time pressure data from a Mensor CPC6000 in LabView using GPIB. I've tried a basic program using LabView VIs 'GPIB Write' and 'GPIB Read' The CPC has two channels and I...
View ArticleWhere can I find NationalInstruments.NI4882.dll version 8.1.20.119?
Hello!I have failed to find that version of dll on ni4882 drivers page. There are lot of drivers from major version 1 to 17 but no 8 at all. I try to use old dll that compiled with connection with...
View ArticleClik here to view.
sbRIO-9607 DIO Serial Interface and CLIP Generator
tannerite wrote:This presentation covers what a CLIP is, how to navigate through the sbRIO CLIP Generator, and how to import a socketed CLIP into your LabVIEW Project.Hi, I have a very related...
View ArticlePCI-GPIB for newport ESP300
I am not able to find the ESP 300, by instrument scanning. I am using PCI GPIB card for communation.
View Articlepxie-5160 issue using IVIScope driver
I am having issues getting my PXIe-5160 4-ch scope to work with the IVIScope drivers. I am taking a measurement over 400us with a min record length of 10,000. When I prepare a reading on channel 0,...
View ArticleVersion conflicts between NationalInstruments,Visa and IVI.Visa in NI-VISA 17
A version conflict exists between NationalInstrument.Visa DLL revision 17.0.0.0 and the ivi,visa DLL revision 5.8.0.0. Based on the AsmSpy output shown below, it seems that NI Visa was compiled...
View ArticleF240 writing problem
I have a problem when I write F240. My F240 board is a 4MHZ crystal oscillator, using DOS to writing with the default and the 10MHZ crystal oscillator setting. Now I know that I need to modify the...
View ArticleCP210x UART bridge in TH1941 multimeter
Hello,I'm trying to connect my digital multimeter with labview 2016, i downloaded the driver for the UART bridge in silicon labs website and all is working OK, in the MAX, VISA test panel >...
View ArticleHow to count the no. of packets received
Hi,I am interfacing a weighing scale to LabVIEW through VISA serial.When weight is placed on the weighing scale ,it generates the string "[xxxxx]" where 'xxxxx' is the weight in grams.The simple...
View ArticleDisconnecting Hardware between VIs in multi-VI application
Hello, I am currently putting together several VIs (to run as sub-VIs) to run in succession in a master VI. The first VI in this series accesses some hardware and then is supposed to disconnect once...
View ArticleProblem of run block labview ultrasonic for Arduino uno R3
I'm student in Asia.I going to make project.I can't run labview for altrasonic sensor with arduino uno r3.Why program don't run? Ask me pls!!! I'm until wisdom. tell me a code labview for run program...
View ArticleRead bytes problem in RS232
Hi everybody I have a device. This device has been designed to send a data stream which is 47-byte in every 100 mSec without any command. When I begin to read the datas, I read 47-bytes data stream at...
View ArticleRS-422 over NI 8431
Hi everybody, I'm using the NI-8431 to communicate with an instrument from a PC.The instrument uses 4 channels - 3 RS-485 half duplex at 1 Mbit/Sec and 1 RS-422 at 2 Mbit/Sec. On the RS-422's channel...
View ArticleControlling MS40 series leak detector (by VIC)
Any one successfully setup communications with this device? I seem to be able to send it commands, but I cannot decode the response it is returning to me. It doesn't seem to be in the format they...
View ArticleMAX crashes OS when a RS-422 PCI card is installed
I have an RS-422 PCI card installed. It is not an NI card nor is it a third-party card intended for use by any NI software or hardware. But, when I open MAX and try to select 'Devices and Interfaces'...
View ArticleLabview and K2600 Series Driver
To whomever, I am trying to write a labview script using the K2600 series driver for labview. The script is for producing an IV transfer curve (drain current vs gate voltage at a constant drain...
View Articlesearching for instruments with NI MAX
I have 2 LAN busses on my system. One connects to most LAN instruments on the test station while the other connects to a small local network. I believe MAX is searching both lines and taking 5-10...
View ArticleClik here to view.
Ni 488.2 connection error in Windows 7 LabVIEW: Error connecting to GPIB...
I am using a SpinCore PulseBlaster LabVIEW ExtensionsIt gives me the message below, Error 0 occurred at an unidentified locationPossible reason(s):LabVIEW: Error connecting to GPIB driver or device....
View Articleleer / escribir datos por solo un COM # de algun puerto serial de la PC en...
¡Hola! para todos los que colaboranTengo la gran necesidad de desarrollar una aplicación a través de un VI, por el hecho de que me gusta programar en LabVIEW. Solo que tengo el reto de como...
View Articlewrite multiple data serially in arduino
Hi everybody, I made a vi to send a multiple data serially to the arduino and my task is to send the swept step frequency manually to the arduino and the code is already uploaded in the...
View Article