Reconfigure VISA Serial Port after error detected
Hello, I'm communicating with a watlow f4 with a rs232-> USB conversion cableI'm using the VISA Configure Serial Port to create my base of communication with the watlow. My program is working fine...
View ArticleB&K Precision PS 9115 not detected
Hi All, I have the B&K precision power supply 9115 connected to my laptop. I do not see the power supply in NI-MAX and device manager. I can connect to a keysight power supply through LabVIEW,...
View ArticleNI USB 8451 U2 Chip??
Hello Every one, I would like to know what component or chip was on the NI USB 8451 "U2" because it was damage and cause my NI USB broke., over supplied voltage. can anyone share me a site for...
View ArticleCMU200 remote control over usb to rs232
Hello everyone,I'm new to working with this kind of device and i have troubles just setting a simple serial link between my computer and the CMU200. I'm using a usb to serial cable in order to perform...
View ArticleContinuous acquisition with TDS1002 over GPIB
I want to capture data from a single channel of TDS1002 connected by means of GPIB, over a long period of rime. I am using LabWindows and IVI driver. To say simple, I want to have a single trigger and...
View ArticleHaving issues with simple serial communication.
Hi,I have optics module which communicate on serial bus. I am using Visa serial bus to talk to it. Bus Frame is like this 1. Start of header : 1 byte2. Address : 1 byte3. Command :1byte4. Data...
View ArticleIssue with NI-VISA detecting ENET-GPIB/1000 resource on RHEL5
Hello, I am having trouble getting NI-VISA Interactive Control to recognize the resource and would appreciate any help. My goal is to communicate with the device through NI-VISA. Configuration...
View ArticleGPIB Timeout Setting
Hi, I am implementing a software control to a GPIB instrument using a loop to poll on the response data. In the Measurement Studio, I have set the GPIB I/O timeout to 10 seconds. But, at the real...
View ArticleUSB-488 and Ni cRIO 9035
Is it possible to use USB-488 with cRIO 9035 Ni Linux based RT controller? (By installing Ni Serial RT to cRIO using MAX)Regards,
View ArticleHow to reset the GPIB ENET BOX.
To whom that is concern.We know how to setup the IP address for the GPIB ENET Box (version C on firmware.) but the assignment for IP address is not successfully. So the GPIB ENET box is bad?...
View Articlesetup the IP address on GPIB ENET Box
I using the Window NT to assign the IP address for the GPIB Box. I can assignment the new address for the GPIB Box (EX: 192.168.25.3).but I can not assignment the new address 120.2.1.0. I do not why?...
View ArticleGPIB-USB-HS problem
Hi. I was using a Window XP SP3 and a GPIB-USB-HS it was working correctly. But virus may have damaged the software. I tried to reinstall to the driver but I am encountering the same problem over and...
View Articleusing Keithley 2400 SourceMeter and either a Keithley 6485 or keithley 487...
Hi guys, I am doing a project whereby i have to collect data from the sourcemeter and picoammeter at the same time. Right now i have the labview IV for sourcemeter, which allows me to collect the...
View Articleexplanation of ke6485 labview program
Hi, I am new to LabView and i am tasked to measure current using a KE6485 Picoammeter. I tried searching the forums and discussion board and i manage to find a labview program which measured the...
View ArticleControlling SR780 via GPIB for Low Frequency Noise Measurements
Hi all,I am wanting to control a SR780 analyser with LabVIEW for a project on low frequency noise measurements that I am working on. I have only used LabVIEW briefly in the past (a few training courses...
View ArticleClik here to view.
How to use PXI-8430/8 for simultaneous communication
Hello, NI PCIe-8430/8 support independent serial communication on each of its 8 ports,which means it can perform simultaneous communication, and here the problem I encountered.Can you help me to figure...
View ArticleVISA USB driver for sbRIO-9627
Hello,I´m trying to communicate with a sbRIO-9627 FPGA board via a VISA USB driver. In the meantime I was able to create with the driver wizard a VISA USB driver for Windows and the sbRIO is detectet...
View ArticleTrouble Communicating with Motion Controller using GPIB
Hi everyone, I'm trying to interface with an old Newport MM3000 motion controller using Labview VIs, but I am not able to communicate with the device. I can program and interface with the motion...
View ArticlePXI-8433
Can we program PXI-8433/4 individual channel to different baud rates? Thanks,Chethan
View Article