set fluke 45 to constant current mode using rs232
Hi, can someone please tell me how to write a program to set the fluke 45 to fixed current mode and acquire voltage readings? Thanks
View ArticleAgilent n3300A constant voltage operation
Hi, I have been trying to use the following progam to fix the voltage output of Agilent n3300A and readout the current measurements. However the intrument is reading out the open circuit curent/...
View ArticleContrôle d'instrument avec Labwindows CVI
Bonjour,Je développe actuellement une application de contrôle d'instrument avec Labwindows CVI et j'ai utilisé l'assistant IO pour réaliser cette opération. Le problème se pose lorsque l'assistant...
View ArticleRead time variable @TIME from 4156c with Labview
Hi, I am using the agilent 4156c with Labview and it works well but, even if i can read voltage or current with labview, i don't know howI can read the variable @TIME. I know I will have to put some...
View ArticleMac VISA remote resource access from Windows
Hi, I'm really new to LabVIEW and VISA. I understand that I can access the resources of another computer through VISA server. I have this Windows computer, which is hooked up to a fluxgate magnetometer...
View Articlegpib communicator in linux
Hi, I'm newbie in NI product and linux. I have install the NI 488.2 card to linux with GPIB-USB-HS, i want to test the communication between linux enviroment and windows enviroment. Here is my...
View Articledoesn't generate COM port in MAX for USB interfacing
hello there, i am connecting tektronix scope TDS7104 via FT232R USB UART connector and connection is established successfully. i am connecting usb socket at COM3 port of CPU. problem is that in MAX,...
View Articlecontrolling servos simultaneously
Hi, I am using a pololu serial 8 micro controller to control 8 servos simultaneously. I am sending commands over the serial port. The approach is to send a 5 byte decimal array that is converted into...
View Articlehow to control DAQ, GPIB and VISA in other language
Hi there, I have GBIP, NI PCI6713, NI PCI6711 card installed and we have labview 7. I am just wondering if labview is the only way to control the GBIP and those DAQ cards? Is that possible to use C++...
View Articlehey guys...how to programme in LabView to retrive datas coming from different...
hey guys... how to programme in LabView to retrive datas coming from different relays through RS485 DB9 port using NI PCI-8431/8 and modbus communication?Please drop the block diagram code also if it...
View Articleduty cycle IVI-driver
Hi, I drive a Textronix AFG320 with its IVI-driver and Labview. But in this IVI and IVI-Class Driver, there is not Duty Cycle fonction. Why ?have you got a solution please ? Thanks,Adrien
View Articlefailure of serial communication
Hi, I have a problem about the serial communication between LabVIEW and a FTDI chip (UART to USB). I cannot read from this serial port. Even no response when I sent *IDN?\n in MAX. Here is some other...
View ArticleSorensen XG 40-21 communications crash
Hi, I inherited a LabView application that controls 30 Sorensen power supplies. It has a communications crash about once a week that is driving me nuts. See the attached image for an overview of the...
View ArticleClik here to view.
PLC with LabVIEW
HiI have a PLC DL06-D0-06DD1 which i need to connect to the PC and then communicate to it through LabVIEW.As I am new to the PLC I I dont know where to start from? Can any one help me to startup with...
View ArticleHas any one setup communication between hagiosonic stargazer and labview
Hi everyone,I am working on a project in which I want to use hagiosonic Stargazer sensor that has a TTL interface with Dani robot and I need to set up communication between the sensor and the robot...
View Articleprogramming manual of chroma 6310
Hello, Can you please help me to get the programming manual for programmable chroma 6310A series DC Electronic load?. Thanks and Regards Rajan
View ArticleClik here to view.
RsSpecAn Instrument driver shows question mark in palette
I copied the RsSpecAn driver downloaded from R&S to instr.lib and user.lib folder. And found there are question mark in palette. I don't know if it it right.Any comment or advice would be very...
View ArticleTransfering measurement data from 4155 to labview
Hello, I'm running into some problems with transferring measurements from a HP4155 to labview. I've tried finding the correct commands in the programmers manual but havent found a definitive answer...
View ArticleClik here to view.
Communication Protocol with RS485 and Yokogawa UP55A
Hi all, I have input the exact commands according to the UP55A manual and pretty sure the connections are correct but my labview doesnt seems to be responding. Also i refer to this link where i got...
View ArticleNo serial COM port available on sbRIO
Dear All, I use the "Visa Configure Serial Port.vi" from "Instrument I/O->Serial" pallet in my application, to get access to the serial com port on my sbRio-9636.When running the application the...
View Article