NI488.2 Installation for Visual Studio C/C++
Hi, I'm trying to control a Measurement device via GPIB. The connection works fine. I want to programm the device with C/C++, and downloaded NI488.2. Including the header NI488.2h works just fine, but...
View ArticlePCI-GPIBを認識しないことがある
Win10 IoT Ent LTSB 2016 PC（488.2 バージョン16.0）にPCI-GPIBを装着していますが、2～10回に1回の頻度でPCI-GPIBを認識しません。 PCI-GPIBが認識されない場合、デバイスマネージャで確認するとハードウェアIDが正しくありません。 正常時...
View ArticleRohde Schwarz GPIB communication. Screenshot sending via GPIB
Hello there,I've got a question how to send screenshots via GPIB. I have Rohde&Schwarz device VECTOR NETWORK ANALYZER ZVM. There is available software called RSCommander. Earlier there was...
View ArticleClik here to view.
How can I monitor the GPIB bus with second GPIB-USB-HS (second PC)?
As below, I want to use the Visual studio C# to monitor the command/message on GPIB-USB-HS bus (blue).How can I use the second GPIB-USB-HS (red) for monitor the GPIB bus (blue)?Can any one give me a...
View ArticleLabview Equipment Control
Hi Sir, Normally we use VISA to control the DC/AC source, e-load, DMM, I/O, matrix, etc.Do you have any kind of standard commands for those equipments? or it is varied from supplier to supplier ?Thanks.
View ArticleClik here to view.
NI VISA using USB gives a Parsing error
Hi All, I am trying to initialize Pacific Power AC Source using NI VISA, communication is TCP using USB to computer, if USB is disturbed Then I loose connection with Power Supply, I create a new...
View ArticleGetting old national instruments pci-gpib 183617j-01 working with Windows 10 PC
Hi Everyone, I'm wondering if anyone can provide me with some assistance betting an old pci-gpib 183617j-01 working with a comparatively new, Windows 10 PC. As far as I can tell, the problem seems to...
View ArticleConfigure electronic load using LabVIEW
Hi I am very new to labVIEW. I would like to control the GW Instek PEL-500 Series Electronic Load from my computer. How do I go about connecting it to my computer using LabVIEW because the GW Instek...
View ArticleUnderstanding how Visa reads device buffers
Hi I have a device Keithley K2602B Source meter which supports NI VISA based "GPIB" communicationLet us say that the I measured four current values and saved these measurements in Buffer1. Now device...
View ArticleTiming issue in reading the buffers from NI VISA
Hi I have a device Keithley K2602B Source meter which supports NI VISA based "GPIB" communicationLet us say that the I measured four current values and saved these measurements in Buffer1. Now device...
View Article"Error caused by remote command" in Keysight 34461A.
Now I want to control Keysight 34461A's multi-meter via SCPI. When I run "SYSTem.REMote" command in PC side, the meter screen shows "Error caused by remote command", later the meter can be controlled...
View ArticlePCI-6221 configuration for new PC
Hi all, installed an old PCI-6221 into a Dell 7090 tower with a PCI slot.Compiled my old version of Labware software 8.6 to 2020 and installed it. Software runs and works, 95% of the external inputs...
View ArticleClik here to view.
VISA Write/Read Hex/String
Hi Sir, For the communication with some sensors or BLE, we need to write the Hex data, also read the Hex data, then parse to what we want. But looks like the VISA VI is accept string, also output...
View ArticlePXIe-1084 Boot Settings issue
Trying to use PXI Remote Configuration SW to setup chassi to Auto-Start when power is connected.Usually by ticking the two boxes. Problem:On one of my two chassis there is no effekt. Any solution ?...
View ArticlePXIe-8398 fiber compatible?
I have a PCIe/PXIe - 8398 system for which my 3m MXI cable is too short. Is there a Fiber cable assembly that I can purchase for these cards?
View ArticleClik here to view.
Basic Visa with Arduino help
Hello I'm very new and trying to do basic communication with LabVIEW and Arduino I followed this tutorial https://www.youtube.com/watch?v=ODJOwD8WklI and everything worked UNTILL trying to choose the...
View Articlemitutoyo lsm-5200 display unit user manual
Does anyone have the USER manual for the Mitutoyo LSM-5200 display unit? I am not looking for the specifications manual but rather the manual explaining what the function of the buttons on the display...
View ArticleRMX-4003 in RMX-4002 left channel not working
I used the RMX-4003 in the RMX-4002 chassis, after a short time the left channel of the RMX-4003 stopped working and all indicators are always on the display. The right channel is working fine. Tell...
View ArticlePCIe-GPIB card not detected
Hi, My PCIe-GPIB card doesn't detect on MAX my PC. I did uninstall the Ni-488 driver, then reinstall driver. After finished install dirver, then instaledl the hardware GPIB card. I opened MAX aand...
View ArticleNI-PCIe-8431/8 & 16
I am using both the NI-PICe-8431/16 and a pair of NI-PCIe-8431/8 RS485 cards in different test set ups and have noticed a “Bug”. When running the NI-MAX tool to validate the cards, I occasionally...
View Article