Find all Instruments on GPIB using VBA
Is there a way to find all intruments on a GPIB. I want to basically do what NI max does when you can view each instrument and then put the instuments in a array. I found this example but does not work...
View ArticleError code when trying to run VISA
Hello, I am trying to run the VISA test panel to see if my system is talking through the serial port to my computer's USB port. I keep getting this error Error opening resource: ASRL3::INSTRVISA: (Hex...
View ArticleClik here to view.
Build Installer - Additional Installers Needed
Hello, I am trying to build an installer using the application builder.There are 3 additional installers needed: Then when I click OK it will show me this:I read about this issue but I can't find the...
View ArticlePXI-4071 Problem activating a reading
Hello, thank you in advance for your interest in our problem. The system configuration is as follows:NI PXI 1033 boxNI PXI-4071 cardPXI-6221 Ni boardNi PXI-6514 cardPC HP I9 The system was working well...
View ArticleIFM SM8601 Flowmeter Connection to USB-6008
Hello, I am using an IFM SM-8601 flowmeter and NI USB-6008. The flowmeter has 4 cables (brown for L+, blue for L-, white for analogue input, black for PLC input). I am trying to use the positive...
View ArticleNI MAX USB device alias disappears
Hello, I have a device connected to PC (Win7) and controlled via CVI using alias assigned in NI MAX. Occasionally after restart alias vanishes from NI MAX leaving only resource name 'USB:: ...' and no...
View ArticleClik here to view.
Communicating with Fluke 9100S Temperature Calibrator via RS-232
Hi, Still pretty new to LabVIEW, so I hope to get some insight and suggestion to the problem. Objective - To establish basic communication with the 9100S Temperature Calibrator via RS-232 (Read...
View ArticleRegarding IV curve
Hello, I have to build a program to for IV measurement of solar cell, but as i am new to labview its very hard to get the same. still i tried doing it with keitley drivers but i am getting eroor 230,...
View ArticleNI IMAX "Open Interface" option not available
Good day, I recently formatted my computer and reinstalled my PCIe-1433 framegrabber. When trying to configure it using NI MAX, the usual option to "Open Interface" that used to appear after...
View ArticleClik here to view.
National Instruments Route Coordinator and NI Device Monitor takes up 100%...
Hi All, We are using Keysight M9018B main frame with PXIe-4141 cards installed in the slots. This is a new system, with Windows 10 OS, 16 GB RAM.NI Route Coordinator and NI Device Monitor occupies 100%...
View ArticleClik here to view.
ERROR : No VISA resources found
I would really like to work through troubleshooting this for everyone who encounters this error! So any suggestions for what else I can check / attempt is SEVERELY welcome! 😉 ProblemAfter a power...
View ArticleClik here to view.
How does cRIO use 3rd party dynamic link libraries to control instruments?
I need to use the cRIO to control the signal source of Holzworth, according to the instrument instructions, I can already use the computer to control.According to the cRIO control instructions, the...
View ArticleIVI driver transport
Hello, I building a program where I wish to have the user select an instrument (in this case an arbitrary waveform generator) from a list of models (DS345, Tektronics AFG31xxx, etc) and point me to the...
View ArticleNI-XNET Bus Monitor and USB8473
We used to use the NI MAx software which had an integrated CAN Bus monitor with the USB-8473. Recently, I tried to get this setup going on new laptop with Win10. With latest drivers, it looks like the...
View ArticleError opening resource: ASRL10::INSTR VISA: (Hex 0xBFFF0011) Insufficient...
Dear NI Community, My name is Sophat Houn, a master student in Photonics and Applications Lab. in Royal University of Phnom Penh, Cambodia. I encountered the problem that " Error opening resource:...
View ArticleClik here to view.
Continuous Serial Write and Read
Hi all,I'm running the example Continuous Serial Write and Read.vi in National Instruments\LabVIEW 2021\examples\Instrument IO\Serial. But i don't know how to pass the string format to command ?? can...
View ArticleNI-VISA Runtime
Hello, I have been using NI-VISA 18.5 Runtime version installer that is automatically launched with our app's setup.exe. I recently found that the installer shows an error message (The "NI Certificates...
View ArticleGPIB-USB-HS does not turn on
I have a GPIB-USB-HS that was working for years but recently stopped working. When I plug it into the computer, the "active" light will be on for ~5s (even though nothing is connected to the GPIB...
View ArticleI have a NI-9202 card, I don't see interface listed when I boot up the NI MAX...
I have a NI-9202 card, I don't see interface listed when I boot up the NI MAX explorer. Also I try to use python to talk to this NI-9202 card, any NI experts can jump in to help (give some guide line?)...
View ArticleGPIB-USB-HS Sending string on Computer Startup
Hi there, I am using the GPIB-USB-HS to control programmable power supplies. I require the power supplies to stay running in order to maintain stable temperatures of the coils they are powering, and...
View Article