NI MAX returning wrong data on non-SCPI instruments
I am trying to use an NI USB to GPIB converter to read data from an HP8563E and an EMCO 1060 turntable controller. In both cases the data that comes back on a read command using the VISA interface in...
View ArticleData aquisition using 82357B GPIB-USB interface for 4395A Impedance Analyzer:
Dear all, I tried to communicate 4395A impedance analyzer with the 82357B GPIB-USB interface using keysight command expert and Labview Add-On Tutorial. I could not able to find the SCPI (Standard...
View ArticleUSB TC-01 showing incorrect temperature on some PCs
Hello, I haven’t posted on these forums before, so sorry if this isn’t in the right place.I have a USB TC-01 temperature recorder hooked up to a K type thermocouple. This is plug and play, although I...
View ArticleI can't see my visa ressource n labview
Hello,I have a GPIB interface connected to a keithley instrument.When using Visa intercative tool I can establish a communication with the instrument. ( image 1)but on labview, I can't find the...
View ArticleVisa read error
Hello, I am trying to create a simple serial communication between labview and an Arduino board using its USB interface. The communication works when I use the serial monitor of the Arduino IDE. I used...
View ArticleTimeout Expired error for RS485 loopback test
Hi everyone, When I was doing a loopback test for a B&B USB to RS-485 mini-converter (4 wires), I am getting the meassage like"Read OperationErrorVISA: (Hex 0xBFFF0015) Timeout expired before...
View ArticleDF_PROFI_II_PROFIBUS_VISA_Driver for 64Bit Operating system
Can somebody help me from where I can download DF_PROFI_II_PROFIBUS_VISA_Driver for 64 bit operating system?
View ArticleClik here to view.
Help understanding this manual VISA write command
, The hardware manual says: What does this look like on labview, right now I have it looking like this for a Z command is it correct:
View Articleneed drivers for GPIB cards that works on MSDOS
I need the drivers for the AT-GPIB/TNT and AT-GPIB cards, the support section of them displays a message that it has been archived and the link to download them is broken, the reason I need them is...
View ArticleInstrument wizard error. Driver not found. LabVIEW 5.1.1
Hello, I am trying to install a driver for the instrument SR830 via instrument wizard. But the error "some or all of the files for this driver were not found. This driver could not be properly...
View ArticleError code -200088,-200284
Hi, I have taken a labview code, when I run it, I faced this error. If I want to fix this, what's more information that I should give? Picture of error is attached。Thank you.
View ArticleHow to control Andor Camera
Hello! I wanna ask help on how I can control the CCD camera through Labview. The model of the CCD is DF887 and I already installed the Andor software for the camera and it's already okay. The software...
View ArticleWinlab32 with a Perkin-Elmer Optima 2000 DV ICP on Windows XP - Windows...
Hi,We have a Perkin-Elmer Optima 200DV ICP Spectorphotometer connected to a (old) Workstation running Windows XP SP1 and have installed Winlab32 instrument control software.Until now, the software has...
View Articlewhat are the differences between TNT5002 and TNT5004
Hi,I am designing an interface card that will include two GPIB controllers (TNT5002) that will operate over PCIe via PEX8112 ( PCIe to PCI bridge ) and have several questions to the forum:I uses...
View ArticleOhaus Ranger 7000 serial communication
Hi, I'm working on a VI to pull data from a commercial bench scale and store it inside an array until I get 10 readings, the thing is that I keep getting a 0 after each reading occupying an additional...
View ArticleThermotron8800 TCP/IP not working
A windows7 laptop was used to interface with the Thermotron8800, the device ip address was on DHCP, 192.168.88.25, when the laptop was set to be DHCP and connected to the Thermotron through ethernet...
View ArticleMini Display
Hi,I am looking for a mini display to connect to NI cRIO-9030, I wnat to mount it on the cabinet door, could you please let me know any brand that you have used before.Thanks
View Article.NET x86 NiFgen Exception
I have the exception produced by function RouteSignalOut Error Message:Instrument error detected. Call the PREFIX_error_query function and examine the error code and error message parameters for...
View Articleerror 10109 with THORLAB DDS220/M and BBD202
I am trying to design an xy-stage. I encountered the error 10109 which says that 'Control HW Communications Disabled'. I have attached my code below. There are 2 serial numbers because I have 2 stages....
View ArticlePCMCIA485 vs USB485
Hello I'm been using one old NI pcmcia485 to receive and send informations to one MVAT electric presse. The PCMCIA485 is obsolete then i bought the new usb485 interface to replace the old 485 PCMCIA...
View Article