Aide Labview Visa programme / Help Serial communication using Visa Labview
Bonjour, voila je suis en projet pour mon école et j'ai des soucis pour lire une donnée d'un port USB, dans un premier temps j'essaye d'écrire une trame et de la lire cependant mon programme ne...
View ArticleClik here to view.
4-Byte IEEE floating number conversion
Hello guys : I've faced a probelm on converting the 4-byte IEEE binaries into floating numbers. I've got the 4-byte binary data from spectrum analyzer SR780 capture buffer. Fig1 Block diagram of VI...
View Articlehello , i have a problem in my labview program, i want to display the...
hello ,i have a problem in my labview program, i want to display the information from the sensor in my Labview using Visa ressource, but the visa configuration does not detect the serial ports of my...
View ArticleWindows 8 OS & NI Configurator 15.0 via using usb-8486 speed problem
Hi all. I have question about NI foundation fieldbus USB Interface(P/N : USB-8486). as you can see my article's subject, I have already using windows8 OS & NI Configurator 15.0. but, this system is...
View ArticleDriver for Texio PW8-3AQP
日本語：Texio の安定化電源PW8-3AQPの計測器ドライバを探しております。もしございましたらどのドライバを使用すればいいかアドバイスいただけますでしょうか。GPIBまたはUSB経由でlab viewを使用する予定です。Lab viewの計測器ドライバファインダーで見ると次の３つのみでした。そのため、どのドライバを使用すればよいかわからないためご質問させていただきました。...
View ArticleHow to interface Intel Galileo generation 2 board with labview
How to interface Intel Galileo generation 2 board with labview. I am trying to send signal from my Laptop COM port to USB 2.0 client port of Intel Galileo Board gen 2. Can somebody help me or atleast...
View Articleserial data myrio
Hi everyone, I've got a touchscreen connected to teh myRIO and I'm trying to read serial data form the touchscreen. The data I need is 10 bytes long and has a distinct first and second byte. When I'm...
View Articleread from the buffer each (ms) labview visa
hello everyonei have a data came each millisecond i want to save this data and clear the buffer for the next data
View Articlehow to transmit data from labview to arduino through HC06
I want to turn on and off a LED(pin 13) on the arduino uno board using bluetooth(Sending the data from my computer bluetooth to the HC06 Bluetooth Module plug-in the arduino uno).1-I paired both deivce...
View ArticleProgram Interrupted by Various Errors
Hello, I am running a VI that controls and monitors the flow rate and pressure of gas using 2 Bronkhorst Flow Meters and Pressure gauges, which all connect to a single USB port. The VI uses predefined...
View ArticleHP 3652A interface with MATLAB
Hi, I am trying to connect to an HP 3562A Dynamic Signal Analyzer (DSA) using MATLAB, with an NI GPIB-USB-HS cable. I have a VISA connection established with the DSA and am trying to send it simple...
View ArticleClik here to view.
VISA reading drastically slowing down at 20Hz (Labview + Arduino + Xbee project)
Hi,I am quite new to Labview and Arduino, so excuse me if I use incorrect terms. I am having some troubles with the following project, I hope you guys can give me some guidance!I have 16 sensors...
View Articleweight scales offset
Hello, We recently bought 2 weight scales from Adam equipment, model number "HCB 602H". We pluged them to a computer using RS 232 communication port. We want to measure continuously a fluid flow into...
View Articlehow to run a USB-485/4 in Windows 10
Hi all this community, I have a question which is: I have a USB-485/4 and I want it to work on Windows 10, as I do because when you connect it gives me no response when making connection to the...
View ArticleConnect servercontroller SC-610 from Harmonic Drive via serial bus as GPIB
Hello I upgraded a computer system from Windows XP to Windows 7 and from LabVIEW 7.1 to LabVIEW 2014. With my VI I'm comunicating with a Harmonic Drive SC-610 servo controller (RS232 connection on my...
View ArticleSerial communication with N-Control unit
Hi, I'm trying to control this unit using serial communication, but I'm not quite sure where to start. The link of the unit is as follows:...
View ArticleUSB-485/4 Ports Failed
In NI-Serial Troubleshooter the first two ports are shown as failed. The second two pass.In Device manager the first two show error This device cannot start. (Code 10). I installed niserial1500f1 on...
View ArticleThird party software Twincat3 of Beckhoff how to receive 9144 through...
Hello, I am now want to use 9144 EtherCAT and the above board, 9215 and 9402, to gather information, now I am writing the FPGA program in 9402 and 9215 to 9402, set up the mode is to electricity to run...
View ArticleNI WSN 9197
Good evening, I have a sensor network device wireless NI WSN-9791 and I'm struggling to it to be detected by the PC in the MAX program.Tou following in the footsteps of a document available on your...
View Articlelabview interface with peaksimple
My project is about design a feed back control system. the PFD is about: Air -> MassFlowController 1 -> toluene --> MFC2--> biofiltration system --> gas chromatography. MFC from...
View Article