NI Package for Windows7
Is there any NI Package manager compatible for Windows7. Can I install NI Visa drivers without installing NI Package manager
View ArticleAgilent PSA Spectrum Analyzer Phase Noise change reference level
I am remotely controlling an E4448A PSA Series Spectrum Analyzer. When asked SYS:VERS? it responds with 1997. I have successfully remotely controlled the Phase Noise measurement data collection but I...
View ArticleClik here to view.
Error -1074117742
Getting error -1074117742 when I use NI MAX to Self-Calibrate a NI PXIe-4080 DMM. I cannot get a measurement out of the DMM but it does respond to pxie commands. I can't find an explanation for this...
View ArticleError -1073807360
Hello, I have a general question about how/if I can get more information about an error code (-1073807360). The Message that comes with this code is "VISA Write in microController_Comm.vi" To provide a...
View ArticleDHT 11 temperature to Arduino -> LabVIEW
Hi, I'm looking for support/help with my little project. It is a simple temperature controlled by a fan in the room. It is primarily a simulation, not an actual project.It roughly looks like this:- DHT...
View ArticleVXI-USB Driver Not Working in Windows 11 22H2, Works great in Windows 11 21H2
VXI-USB Driver Not Working in Windows 11 22H2, Works great in Windows 11 21H2 This means I have to roll windows back to 21H2 and permanently turn off all Windows updates as Microsoft no longer cares...
View ArticleClik here to view.
Rohde & Schwarz SMBV100B - Generate signal through Labview
Hi, I am trying to generate a LoRa signal with a R&S Vector Signal Generator SMBV100B at labview. I downloaded the driver and tryed this inicial VI, but it keeps givin me the error bellow. The IP...
View ArticleThird party driver installation in cRIO
Dear Community,unfortunatelly previous posts on this topic did not help so I am making this new thread. I am trying to communicate with a USB device using my cRIO-9203. The USB device needs the CP2102...
View ArticleMKS 946 Vacuum | Visa Read Problem
Dear Community People, I am using LabVIEW to get flow rate data from LabVIEW. I made an easy code(withoutwhile_loop.vi) using visa write and read. It reads the command. For example, for @253FR6?;FF it...
View ArticleVNA hp8510c and matlab control
Hi,I am a new user of Hp8510c micorwave mearsurement system. In our lab, we are using matlab and Gp-ib to control the system.However, when I finished the 1 port s11 calibration and saved it. Then I...
View ArticleYokogawa WT300 Series Meter LabView THD Values
I currently have a LabView program that reads current, voltage, power, etc. off of the Yokogawa WT310 power meters and saves it in a .txt file. However, I cannot seem to get the THD (A %) value from...
View ArticleInstrument not detected
Hello Everyone, I am trying to establish connections with Keysight PNA N5222B and Agilent VNA E5701C using the appropriate visa drivers via USB o Ubuntu 20.04. I am using the ni Hardware configuration...
View Articlegpib488.dll
Hello,Where or how is it possible to found or dowload gpib488.dll ( It's for C# interfacing) Best regards Mathieu
View Article5-volt output usb-8451 vs 8452
I'm trying to clarify the specs for the 5-volt out on the usb-8452. The 845x hardware/software manual says the module can only supply up to 20 mA. Yet, the USB-8451 has a maximum of 230 mA. Is there...
View ArticleAgilent 34410A cannot connect over ethernet
I can connect to my Agilent 34410A over USB, but not over ethernet.When I plug in an ethernet cable, the left LED turns a solid green, and the right LED shows no light. I've set a static IP on the...
View ArticleGarbage on a NI-9870
I'm new to the cRIO and LabVIEW world. I need to read streams of NMEA-0183 formatted sentences (ASCII) on a cRIO-9040. I have installed an NI-9870 for that purpose. I developed a small VI in LabVIEW...
View ArticleMultiple instances software - Release unused COM ports
Hello all,I am working on a project, where the software is built to .exe form.The .ini file that accompanies the .exe file is setup to allow multiple instances of the software to run simultanously.A...
View ArticleHow to control a can bus device
Hi Sir, I did not experienced can bus device control, but it seems it is very common for automotive.Thus I want to know the logic clearly: 1. Firstly the PC or laptop need a can card, or a convertor,...
View ArticleNI-9870 Max Baud Rate
Hopefully this is an easy question. Per the spec, the max baud rate for the RS232 port on my cRIO-9040 is 115200bps. What is the max baud rate allowed on an NI-9870 (Scan Interface)? For the NI-9870...
View ArticleClik here to view.
Implementing EOI for pyVISA (\n and then what?)
According to the manual for a hardware I'm trying to automate using pyVISA, termination has to have LF and EOI (end or identify). However, how do I ensure EOI happens, and what exactly is EOI? From...
View Article