IVI-COM driver problem--no registered classes warning when trying to connect...
Hi all, I am trying to control TekTronix RSA306B with Labview 2015(64bit) via an IVI-COM driver TekRSA300IVIDriver_1.0, according to a tutorial--Using an IVI-COM Instrument driver in LabVIEW...
View ArticleSorensen/Ametek XG series USB LabView Control
Hi there, I have a Sorensen/Ametek XG 300-5 programmable power supply and I am trying to control the power supply using labview (V.2013). I connected the power supply to the computer via USB cable and...
View ArticleClik here to view.
PyVISA with Keithley 2400 SCPI
Hi, I'm trying to ask a Keithley 2440 to loop through relatively fast sets of 4 wire measurements, report the data, and repeat. I have tried RS232 serial communications with pyserial, which worked...
View Articlecomputer crashes for inductive load
Hello, I my application, I am trying to test a 12V DC motor through a labview program i created.Connection diagram is as shown in the figure attached.I am using NI USB 6002's analog output 0 to...
View ArticleUSB-8451 pull up resistor
Dear all, I'm using the 8451 as i2c master, and for some reason (not important for this discussion) I need to use one of the 8451 pins as a 3.3V voltage source.I chose a DIO pin for the job and with...
View ArticleClik here to view.
Communication issues about Basler acA2040-180km camera and PCIe-1473R via...
Hi, We have Basler acA2040-180km CMOS camera and trying to communicate the camera with PCIe-1473R-LX110 via cameralink. We have tried to follow the KnowledgeBase in NI (Ref.1 and 2) to establish the...
View Articlecontrolling a instrument
Hi Everybody, For a instrument which has LAN input is controlled from a PC, is it enough to make the Internet connection of the instrument and PC? Is it necessary to use any device between the...
View ArticleClik here to view.
the relationship between Force and Voltage and Torque in Inverted Pendulum?
how demonstrate the formula ?the relationship between Force and Voltage and Torque?how to prove that this formula?plz help me tombe0.vt93@gmail.com
View ArticleSending Pelco-D or P commands via RS232 to RS485 converter
Hi, I am trying to send series of commands in decimal format using a RS232 to RS485 converter to a camera that has a zoom control. I have a program that will let me test the commands to the camera to...
View Articleibnotify and nipalut.dll
Hi everyone I am trying to build a custom application to use a NI GPIB-USB-HS adapter. The code is written in cpp and I use QT on windows 7 and windows 10.For the moment, I compile in 32bit using...
View ArticleCan the USB-GPIB-HS be put into slave mode (non controller mode)
Can the USB-GPIB-HS be put into slave mode (non controller mode)? I know the PCI versions can be but not sure about the USB-GPIB ones.
View Articlecontrol via Ethernet
Hi Everybody,An instrument which has LAN input was connected the internet and was seen in the MAX. When I opened the test panel in the MAX, error was given. VISA: (Hex 0xBFFF003E) Could not perform...
View Articlemodbus example serial slave
Hi,i am using Modbus serial slave example to communicate with the modbus device.this example works well when i use "Modpoll" at the other end but not with the "Real term " Sniffer please help Thanks...
View ArticleUSB-232 slow under Windows 10
I have a Labwindows/CVI 2016 application that communicates with a bunch of Eurotherm temperature controllers via RS-232 using a NI USB-232. I have been running it for several months under Windows 7 and...
View ArticleAndor luca is not shown in interface of NI-MAX
Good morning guys, I have the following problem:The camera is not displayed in the NI interface. It's available:- Andor Luca (recognized by PC, the camera is compatible with Labview) connected with USB...
View Article420 Query-unterminated
when I try to communicate to Keithley Model 2000 by GPIB-RS232,I send "*IDN?\n" it is OK. When I send another command like ":CONFigure:FRESistance\n" ,the device show " ERROR -420 Query unterminated"....
View Articlelinking gpib-32.obj in Visual Studio
Hi... I have recently started migrating a large series of projects under a single VC++/MFC solution from VS 2005 to VS 2015 under Windows 7. I downloaded and installed NI-488.2.15.5. I ran the updates...
View ArticleLooking for a driver for a NI PCMCIA-CAN Series 2
Hi, I have a NI PCMCIA-CAN Series 2 Card and need to download a driver for it. The following link is a old version driver for Windows XP/2000/ME/98/95/NThttp://www.ni.com/download/ni-can-2.1.2/262/en/...
View ArticleHow to stop re-assigning serial port names?
Hello, I have a generic PCIe serial device with four ports. It's not an an NI device, but the ports appear in MAX. Does anyone know why changes to the NI setup (e.g. moving an NI card from one PCIe...
View ArticleNI-VISA and openSUSE Leap 42.1
Hi everyone, I'm trying to use NI-VISA on openSUSE Leap 42.1 (it says here that Leap 42.1 is supported) but whenever I try to run ./INSTALL the following error comes up: ERROR: Kernel source does not...
View Article