Errors when connecting RS232-USB to LabView through NI MAX
Hello, I am currently trying to operate a Lumencor laser array through LabView. As of right now I am using a FDTI RS232-USB adapter. In NI MAX, I am able to identify my device (COM-3, see attached...
View ArticleUsing NI USB-GPIB to control Zeiss C90 CMM controller
I have a Zeiss CMM running PCDMIS 32bit on Windows XP with PCI to GPIB (488.2 2.7.3)If the controller is 8bit but works with my 32bit system already, can I export the VISA config file, change to a...
View ArticleGPIB to USB randomly disconnecting
I am using windows 7 to communicate to 6 devices through GPIB with the GPIB to usb hardware. Lately I've been running into the problem of getting a driver error after a few hours of testing. When I...
View ArticleCLIP Generator for Serial TTL on SB-RIO
1. I'm unable to read and write to VN-100 sensor. The sensor is connected to SB-RIO 9627 using 3.3volts TX RX lines (PIN 8 and 9 on the sensor). Using CLIP generator in LabVIEW I have setup two pins...
View ArticleNew to LabView and need help!
I'm probably in the wrong forum but didn't know where to start. I'm very new to all of this, but want to learn - this will probably be very easy to most of you. I have a 2 wire electromagent and want...
View ArticleGetting I2C data
Hi, I m currently having a project that require me to get data from an I2c device (HMC5883L Magnetometer) using an I2C to Usb connection (http://www.robot-electronics.co.uk/htm/usb_i2c_tech.htm). Im...
View ArticleSecond Instrument issues EADR (3) when our device is connected as an instrument
Using the NI PCI-GPIB we have connected our device (a part handler) to a teradyne test system and we have addressed our software to be a listener ie not a bus controller. When the Teradyne system test...
View ArticleProblem Event CLR20r3 when open a XX.exe(use NI VISA)
Hi specilist , When I run XX.exe which use NI VISA control , it ended and the infor Problem signature:Problem Event Name: CLR20r3Problem Signature 01: RFPowerTools.exeProblem Signature 02:...
View ArticleCommunicating with two SR830 Lock-in instruments using one GPIB-USB interface
Hey All, I need to talk to two SR830 Lock-in instruments at the same time. They both seem to have the same GPIB Primary address. Hence i am unable to communicate with them using a single USB-GPIB...
View ArticleControlling a MARKENRICH Relay Tester
I have developed a LabVIEW program to replace the original DBase driven program to operate the MARKENRICH RT-250 Relay Tester. With the lost of support from Microsoft on DBase files, the origianl...
View ArticlesbRIO 9607 IP address and little more problems
Hi, I just got a new sbRIO 9607 to do a project. I powered the device with a 9VDC 300mA power supply and connected to the development computer with a cross-over ethernet cable. I use LabVIEW 15.0 and...
View ArticleVISA: (Hex 0xBFFF0015) Timeout expired before operation completed with...
Hi everyone I'm beginner in labview and I'm getting the error: VISA: (Hex 0xBFFF0015) Timeout expired before operation completed. This is my vi file. I cannot understand what the problem is.. PS: I'm...
View ArticleUnable to Read SRQ Request over GPIB Bus
Hi Guys , Am a newbie in GPIB Programming with no experience. I am currently working on a project which require to Listen to data communication between Controller and Device via GPIB Bus. The...
View ArticleClik here to view.
Agilent DSO5054A waveform read problem
I'm using the Agilent DSO5054A with GPIB connection.I tried to get a driver but there are two ...DSO5054A DriversWhich one should i use?I already have installed the IVI driver but there is the problem...
View ArticleInterface between HYDAC HMG 3000 and Labview
Hello everyone,We already have a HYDAC HMG 3000 to acquire signals of different sensors (pressure, flow, ...). This interface is already connected to a computer by a serial USB cable (Type B to Type A)...
View ArticleAgilent N5763A driver
Hi,I try to controll my Agilent N5763A source with LabView.I'm searching for a driver but I can't find a good one.Is someone here who has a link for me?How can I install the driver? BestWEni
View ArticleMeasuring both voltages and resistances with DMM + Switch every second
Hello, I have a PXI-4071 DMM and a PXI-2527 Switch. I need to measure 24 differential voltages and 2 thermistor resistances every second. I'm trying to do switch scanning with the DMM. The switch will...
View ArticleHow to detect instrument connected to USB port on sbRIO 9607
Hi, Background:I have a IMU sensor that I connected to PC's USB port and was able to acquire data in JSON string. I used VISA with a virtual COM port as VISA source. Just opening a connection was...
View ArticleClik here to view.
Keysight E5270B not showing in ni-MAX, however detected in Keysight IO...
Hi all,I'm completely new in Labview and Instrumentation. I got into this field to enhance my skills and undergo some measurement project.I installed keysight IO library suites and it can detect my...
View ArticleListen only GPIB Labview
I have an application where I need to listen only on the GPIB bus (NOT be a controller or interfere in any way with the controller). Then, when I see the information come across that I'm looking for,...
View Article