Capturing Torque Data With Mark-10 Force/Torque Sensor
Hello community.I need to build VI that will collect torque data using a Mark-10 torque sensor. It connects to a PC via usb and collects data with a canned sw solution that is buggy. I would like to...
View ArticleUSB RAW device freezes my LabView and Matlab program
Hello everyone, I am trying to figure out if I am the only one facing this problem. I created NI VISA driver for my HID device. It was working fine but now as soon as this device is connected to the...
View ArticleENET-232/4 installation
Hi All,I bought an ENET-232/4 and connected it to tried to my Windows XP PC with an Ethernet cable. I downloaded NI-Serial 15.0 and installed it onto my PC with NI-MAX 15 also. I went to...
View Article(Hex 0xBFFF0011) Insufficient location information
Good day everybody, I have Tabor WW1072 AWG connected to a hub to which my notebook is connected. I can ping the device, I see it from NI MAX, I see it from VISA test panel. But when I try to contact...
View ArticleProblème driver USB-7845R/SCB-68A
Bonjour tout le monde J'ai un boitier USB-7845R avec une carte SCB-68A. Je n'arrive pas à obtenir le bon driver pour que mon matériel soit reconnu dans Max.J'ai téléchargé pas mal de choses mais rien...
View ArticleRemove NI MAX 15.0 and install older version
I installed NI MAX 15.0 through a NI Serial installation. It didn't have what a manual said about an ENET. So I reinstalled NI Serial from the DVD that came with the ENET-232/4. Now NI-MAX doesn't...
View ArticleParameter out of range
HI I get "Parameter out of range" in SR830 driver.I tried the possible solution i could. figure. Pls guide.
View ArticleProblem with Serial Communication
I am trying to write "\x59c\x3aimagesnap" to a scanner using the VISA serial read and write vi and I'm having problems reading the image from the scanner. When i type the same command in a...
View ArticleEtherCAT Slaves
Hello. I am not sure if I navigated to the correct location or not. What I am trying to find out is, what is the ingress protection of the NI slave modules that interface with with an EthernetCAT...
View ArticleClik here to view.
LD 400 Aim-TTi INSTRUMENTS Labview Drivers
Hi,I would like to ask, if anyone word with Labview with this device? I mean DC load Aim-TTI Instruments http://www.newark.com/aim-tti-instruments/ld400/dc-load-fixed-80a-80v-400w/dp/67X5300 I s there...
View Articlecommunication problems with measurement devices (GPIB)
Hello, I'm using five measurement devices for my test rig and sometimes I have communication problems with two measurement devices. It is weird, because this problem is only sometimes and not always. I...
View ArticleAM-9898 HART communications CompactRIO Module not recognized by NI 9148
I am running a small scale lab test since several years using LabVIEW 2012 and the Compact RIO NI-9148.Recently I have bought the extra module AM-9898 to expand the system. I have mounted it in the...
View ArticleExecute different DAQmx tasks based on DAQmx output buffer index
Hello everyone, I am a beginner labview=>DAQmx user and i run into the following problem/challenge; I am sending a array of data (signal) to a USB DAQmx device, and i want to switch two powersupply...
View ArticleArduino, VISA, Serial Communication
Hello to all the users,I'm new here. What I'm trying to achieve is to graph in real time data from two accelerometers connected to an arduino uno. The problem is that I am not receiving anything if I...
View ArticleMissed bytes in VISA communication
Hi, I created two programs with labview which communicate together using virtual COM ports that are connected properly.The first program sends a paquet containing an integer n to the second program...
View ArticleLabVIEW interface using Firmata protocol to control Arduino microcontroller
I would like to use a LabVIEW interface to control an Arduino microcontroller using a Firmata protocol. The desired goal would be uploading an Arduino sketch with the Firmata functionality so that the...
View ArticleUsing a Labview VI, I send a query command to my device and the proper data...
I am new to LabView and GPIB so I apologize if this is something trivial but I could not find anything related...I am not sure if this is realted to my device, my VI, GPIB or a combination of such. I...
View ArticleCan't Talk with Omega CN7200 Temperature Controller
I have an Omega CN7200 PID temperature controller that I’m trying to talk with using VBA code and NI-VISA. The CN7200 has a RS-485 bus, but I bought a 485-to-USB converter from Omega. As a test, I...
View ArticleHow to create ampere control signal (4-20 mA) from voltage control signal...
I have to control 4 proportional valves (Bürkert 2873 x 3 & 2875 x 1) installed on a gas line. These valves control signal type is 4-20 mA. I have a NI USB-X 6343 daq with 4 AOs of -10 - 10 V. How...
View ArticleControlling AC Voltage Output via LabVIEW
Hi, I'm trying to control an AC voltage output from 0~250V using LabVIEW, but I couldn't find any device that does this kind of operation and can communicate with LabVIEW. All the NI DAQs available...
View Article