8903b
Hi I have a 8903B audio analyzer and I am try to get it to communicate with my laptop using Labview via a Agilent 82357B USB/GPIB Interface but Labview can not find the analyzer, i found the correct...
View Articleuse serial pump labview back send
Hi.I have a Cole Parmer pump, which accepts serial commands over DB-9 RS-232 (Manual attached as "ColePalmer-MasterFlex LS 7551-00 P3.pdf"). I have connected it to a laptop via a USB/Serial adaptor and...
View ArticleHOW CAN I GET THE TIME IN EXCEL SHEET USING WRITE TO MEASUREMENT INSTRUCTION
HI, I am using GET TIME IN SECONDS ,and after that i placed SECONDS TO DATE /TIME instruction ,and i had taken a write to measurement file instructionto get the time in excel sheet. Now i am not able...
View ArticleConnecting shutter Uniblitz to computer with rs232c
Hi everyone, I would like to connect a shutter (Uniblitz VCM-D1) to my computer. I read in the manual that this VCM-D1 can be controlled by a an RS-232C computer serial signal COM port and which must...
View ArticleI/O Trace ..
Hello, I'm trying to capture SCPI commands from LabVIEW 2012 VIs. The attached file is from I/O Trace 3.1. Some of the captures contain ".." and in some cases I am able to get the full string by going...
View ArticleSeñal escalonada
Buenas tardes.Quisiera realizarles la siguiente consulta: estoy realizando un proyecto en el que se adquire una señal biomédica, se la muestrea, se la codifica según el algoritmo ley-u y se la...
View ArticleVISA port spy
Is there a way to programmatically monitor a serial port (without taking control of the port or otherwise interfering with an existing connection)? I know I can use third party applications like...
View ArticleLabview to communicate over usb with a Danfoss VLT AutomationDrive FC 302...
Has anyone used Labview to communicate over usb (or RS232/RS485) with a Danfoss VLT AutomationDrive FC 302 adjustable frequency drive ?ThanksHierromovil
View ArticleMAX - Message from Webpage
Greetings Everyone, Sorry if this has been posted in the incorrect forum. When I am using MAX and select the Calibration Tab for the PXI-5114 or PXI-4065 a dialogue box "Message from Webpage"...
View ArticleIVI Configuration with PXI-4110 in TestStand
Hello All, Set-Up:PXI-1033 connected through MXI to a PC running Windows 7. LabVIEW 2014. TestStand 2014 (32-bit). PXI-4110 Power Supply and PXI-4070 DMM. In MAX I can open both soft panels and control...
View ArticleSafely Remove GPIB-USB-HS Devices
Hello, I have several GPIB instruments connected to PC through GPIB-USB-HS. I know normaly for USB devices I need to do the safe removal. What should I do in this case to remove connections while...
View ArticleWatlow F4 GPIB-USB-HS Error-1073807331 The Specified attribute is not defined...
Hello, I am trying to run the Watlow F4 Controller Driver downloaded from NI website to control an environmental chamber. I connected the GPIB port to PC using a GPIB-USB-HS cable. The GPIB to ModBUS...
View ArticleClik here to view.
Modem SMS Gateway for Labview
hi,i wanna ask on labview which one modem that support VISA for sms gateway in labview ?i have 2 choice first Wavecom m1306b USB : and Wavecom m1306b RS-232 : i hope you can help me for choose these...
View ArticleTDK-Lambda Power Supply error
HI all I am trying to communicate with TDK power supply (LAN supported model) through ivi drivers. I have created the logical name of the ivi driver and mapped it with niDCPower driver. When I am...
View Articlefrequency change through serial port
i am working on a modem and use to change the frequency of modem using serial interface comand. i want to know how to do that in Labview
View ArticleKeithley 2220-30-1 extra voltage
What I am trying to do is to control the power supply where I can control the voltage step at time intervals. My issue is that each time i run the VI the 2nd channel is not being used will give out a...
View ArticleError - session handle nor valid for ivi
Hi All I have posted this question in existing thread also I guess. I am trying to control TDK lambda power supply through LabVIEW using IVI drivers.logical name set in a MAX is same as what I am...
View ArticleClik here to view.
strange corruption when using U8903 instrument driver
Hallo, this screenshot shows some strange corruption, when debugging some testcode with CVI2013SP1 on Windows 7, which is using the Agikent U8903 instrument driver: As you can see, AGU8903ni_Initialize...
View ArticleSending data serially from one port to another using VISA read/write.
Hi,I have found a program o Labview through which one can communicate on a single port using a loopback adapter.But now I need to serially communicate between 2 different ports using labview..Plzz help
View Articlelms 200
Hello,i have installed the plug and play driver for the sick lms2XX but when i run it, always it gives me the same Error i tried alot to solve those problems but i couldn't, i tried even to build my...
View Article