LabVIEW and OceanOptics USB2000
Hi everyone,I am a new LabVIEW user and I am trying to drive the USB2000 spectrometer with LabVIEW. I followed the procedure descripted in...
View ArticleNI-VISA native 64 bit binary support in Linux
Hi, Currently though NI-VISA is supported on some Linux platforms the binary installed is only 32 bit binaries. Does NI plan to add native 64bit binary support for Linux platforms? ThanksShreenath.R
View ArticleClik here to view.
Old visa open, error code 1073807343, using VISA with a GPIB device, and VISA...
Hi everyone, I'm trying to get a SRS model SR720 LCR meter (manual on this page) working with LabView, connecting it to my PC with an Agilent 82357A GPIB/USB interface (manual on this page). I'm...
View ArticleNI Visa Server can't find remote expansion chassis
Hi, I have a 9149 expansion chassis with a 9871 RS485/RS232 serial module connected to it. I have installed VISA and VISA server on the expansion chassis and configured it to accept all remote...
View Articleaquisition de RS232
Hi, I'm working on a project to aquérir of data of a photovoltaic cell (voltage, temperature ....) ( liason serial RS232 ) the problem is that the transmitter sends us a frame which is not know the...
View ArticleIndependent instruments through same USB port
Hello there, I want to control two different instruments through Labview: one applies pressure to it's outputs, the other, independent from the first, measures the flow rate of the outputs. I want to...
View ArticleCanI programmatically set PXI 8431 ports to half duplex (two wire)?
Hi,I'm using a PXI-8431/8 RS485 card for half duplex comms. I am using the usual VISA serial port setup for baud rate, etc, but I also want to set the port mode to two wire, no handshake.At present I...
View ArticleRe: yOKOGAWA-LABVIEW
Hi, You posted at the wrong board. This board is only for LabVIEW version conversion.I will ask the moderator to move your post and I will answer you. I just need the check something. Kees
View ArticleImport data from a PCV in LabVIEW
I am using a PCV Sensor of Pepperl & Fuchs GmBH. It has a RS 485 interface so I am using a USB-COM Serial convertor.I am trying to use VISA to import the data from the sensor but its not...
View ArticleUsing ivi driver for keithley 2410 on visual c#
Hello, im pretty new to controlling instruments. I've been struggling with using the ivi driver found here for the keithley 2410 on visual c#, i already installed a driver for the agilent 34401 and...
View ArticleClik here to view.
34461A Min-Max Not available like the 34401A
Hello, The 34401A is not longer available in Canada. We need to change and use the 34461A as a replacement and we are having trouble with the peak-to-peak measurements (We are using LabVIEW). We use...
View ArticleNeed manual for Ruska Series 7000 Digital Pressure Controller
Hello Does anyone has a manual for Ruska Series 7000 Digital Pressure Controller (7010-705N) ? I am trying to control it through GPIB in Labview. Many thanks ffl3883
View ArticleN8754A- Power supply does not output the configured value at the first...
Hi There, I am new dealing with instruments. I am using Power Supply N8754a. I downloaded the instrument driver from the below webpage....
View ArticleHaving issues with simple serial communication.
I followed a tutorial online to start learning basic serial communication. The tutorial involved shorting pins 1 and 3 on the Comm 1 port, and writing a simple program (attached). I edited the program...
View ArticleControlling Mainframe Module with PyVisa
Hi, I have a Stanford Research System SIM900 Mainframe and I can communicate with it using Pyvisa. Now, I would like to communicate with the PID module SIM960 connnected to it. I can send commands such...
View ArticleNI USB 6212 -Generate signal
Hi , I want to generate a previously recorded signal using the analog output of NI- USB 6212 daq. The signal is hard to model mathematically. Is it possible to somehow regenerate the signal on the...
View ArticleConfiguring serial port advanced setting
Hey Guys, I am working on one of the project where I need to access the PORT advanced setting programatically in LabVIEW. But the serial APIs (VISA) in LabVIEW is application layer APIs. Please help me...
View ArticleNeed some help controlling Ruska 7000 through Labview
Hello, I wanted to control a Ruska Series 7000 Digital Pressure Controller (7010-705N) by sending a recipe of different set point and durations through labview. The ruska has a GPIB port. I have a GPIB...
View ArticleWatlow F4 with GPIB connection
Hello I have a chamber that uses Watlow F4 controller with GPIB connection. I would like to control it by sending a recipe from Labview. I found this driver on NI website :...
View ArticleCan I use GPIB instruments via GPIB-USB-HS and NI-VISA on MacOS with Matlab...
I've just installed NI-488.2 (14.1) and I can see my GPIB instruments in the NI-MAX app. However I can not find them in the tmtool function in Matlab. Aparently Matlab on mac does not support GPIB...
View Article