How to refresh visa resource list
Hi, I have a device connected on COM4 of the system. Initially LabVIEW finds it. Then I send a RESET command (VISA write) to this device connected on COM4. As a result of the RESETcommand, the COM4...
View Article1073807202 error in Keithley 2401 SMU
Every one. I am using Labview 2012. I am trying to interface Keithley 2401 SMU with laptop via Keithley-GPIB KUSB 488B. When I am trying to run the program, it is indicating error 1073807202. I have...
View ArticleNI USB-GPIB-HS not recognized by LabVIEW 2013
We received a brand new NI USB-GPIB-HS today. It is recognized in NI-MAX along with the 3 instruments connected. Yet, in LabVIEW 2013 SP1 (32-bit) none of the instruments is recognized.I drop a VISA...
View ArticleProgramatically remove devices from Max
I have one laptop that can be connected to different cDAQ systems. Each system is identical built with a cDAQ 9178 with 4 modules. The VIs are written using DAQAssistant for data collection. Every...
View ArticleClik here to view.
how to know the GPIB address of instrument?
I have a Prologix GPIB-USB connected with an Anritsu power meter ML9001a. In the Prologix webpage, it says to communicate with an instrument in Labview, Send ++addr X terminated with Line Feed, where X...
View ArticleIVI and interchangeability
I am developing a C# application which will talk to some power supplies over TCP/IP. I am not using Measurement Studio.I would like to have the ability to swap out one or more of these PSUs for another...
View ArticleCapturing Images or Triggering GoPro
Hey Guys, We are trying to capture images from a GoPro or similar device to make a timelapse of wear to a part throughout a test that is being run by a Labview program. We want the camera to capture...
View ArticleVISA option in Instrument I/O pallet not working
Hi, I am using Labview 2013 version and there seems to be some problem with my VISA pallet. I am doing a project on patient monitoring and i have started with the temperature sensing part using...
View Article6221-2182A to plot IV of FET
My Professor has asked me to make a program to measure the IV of a FET using 6221 (to source/sweep current) and 2182A (to measure voltage). We are using these instruments as the device is made of very...
View ArticleNI 9234 and 9264 synchronization issues
Dear all, I have a NI 9264 analog output that is connected to a current control board and a NI 9234 analog input installed on a cRIO-9024. Basically I specify the current I want to output and I measure...
View ArticleReadString() get time limit exceed to complete operation error
I have a device name Time Electronics 5075. I am trying to use the SimpleReadWrite.2010 in National Instruments\NI-488.2\Examples\DotNET4.0\SimpleReadWrite\cs to comunicate with the device.I can open...
View ArticleGPIB/usb connection loss and OVP freeze
I'm running multiple keithley 2410 power supplies using the agilent GPIB/USB 82357B interface. The power supplies are read continuosly and then set when needed to a new value. The power supplies keep...
View ArticleClik here to view.
pump 703007
Hi, I try to control PHD ultra pump 703007 through LabVIEW. During configuration, this error will pop up after the whole program running about 1 minute or so: Error -1073807360 occurred at Property...
View ArticleClik here to view.
EPWR problem with GPIB-USB-HS
Hello!Usually I've found the answer with Google or from the forums or just being stubborn until I solve the problem but no such luck this time Anyway, we have a growing problem with our production...
View ArticleStandalone application on serial communication
Hi, I created a VI using VISA communication to fetch the measurement made by a multimeter which connects on the USB port. Now, I wanted to created a standalone application so that I can connect my...
View ArticleCSZ and EZT-430i controller
Hi to all!! I'm really new in this community but not so new LabView, so I hope this question is not too banal. I'm usic a CSZ Microclimate chamber, they use a new controller instead of Watlow F4. It's...
View ArticleDropped commands via ethernet connection
Hello, I seem to have commands dropped whenever I use ethernet connections as opposed to GPIB or RS232. I do not know if it is due to timing but depending on the instrument the more frequent the...
View ArticleVISA: (Hex 0xBFFF0015) occurs when I try a query to on 4400
Below is an ttachment of the screen when I try a Query to the INstron 4400. Also attached is the NAIO trace. Read OperationError VISA: Hex(0xBFFF0015) Timeout expired before operation completed. When...
View ArticleIVI-com PowerMeter: Getting to Channel and Measurement interface and using...
I need a bit of help for the proper usage of the Channel and Measurement interface of IVI-COM driver. I have a sucessfully used the Active-X Automation Open, then the intiate methods via the class...
View ArticleLabview Program will not communicate with my NI USB-6210 w/ 3 pressure...
I have been using a labview program for over a year now that has allowed me to see readouts of three pressure transducers. The program has quit reading the 3 transducers from the USB-6210. My computer...
View Article