MAX does not see PCMCIA-GPIB or GPIB-USB-B
I am using a legacy Windows XP SP3 system with MAX 3.1 and NI-488.2 V2.1. I use either a PCMCIA-GPIB card or a GPIB-USB-B. When logged into an administrator account there are no problems; both devices...
View ArticleAgilent 34420, Instrument driver "down rev"
Hi all, Unfortunately I am stuck with Labview 8.0 and need to use Agilent 34420 instrument driver. The versions I found online are not compatible with Labview 8.0. Is there a way to down rev the...
View Articleiblck release after computer crash or network failure
We are controlling equipment using ENET/1000 devices. The controlling computer has a redundant computer in case the primary fails. We use iblck to protect the bus when the equipment is under active...
View ArticleVirtual Lab
Microcontroller(like arduino) is connected to PC.And i want to programme it from far end PC(Through internet)..Is it possible to develope this kind of application in LabVIEW ? I am ready to do...
View ArticleI want to connect the midilogger gl800 of graphtech's company with my PC...
plz give me directions to get the data from midilogger.here i am submitting the user manual.
View ArticleLabivew program for KE6487 picoammeter
Hello everyone, I have limited knowledge about labview and have been trying to learn labview through online help and youtube videoes. Now my professor requires me to make a VI that will measure...
View ArticleN6705B connectivity via GPIB interface in UNIX
Hi i had an N6705B device my requirement is like below I need to control this device via an GPIB interface in linux PC.for the above i am using an GPIB to GPIB cable and connected the N6705B and amy...
View ArticleSCPI commands
Hi can any one let me know how to send SCPI commands to an agilent device over USB itnerface, i installed USBTMC drivers and the device is listed out in the /dev/usbtmc0, now i have to send the SCPI...
View ArticleRuggeduino With Labview for Production Enviroment?
We are looking at the Arduino and LabVIEW option for a large scale production enviroment, however, I'm a little worried about the protection of the Arduino. I've recently seen the Ruggeduino by Rugged...
View ArticleNI-USB-8451 1.8V logic not working - Error
Hello, I have an NI-USB-8451. Using LV13 I cannot set up the device using1.8V logic. I get an error on the first argument, which is the logic level. Work fine for 3.3V. My pullup enable also fails, but...
View ArticleAgilent DSO5054 timestamp problem
Hello everyone! I'm using Agilent DSO5054 oscilloscope with LV to measure voltage. I've downloaded the appropriate driver for it, called ag6000a. My computer is connected to the scope trough LAN cable....
View ArticleProblems in Installing NI 488.2
Hi, I am trying to install NI 488.2 2.7.3 on Windows XP SP3 (32-Bit). However, during the installation, I am getting a message of Rolling Back Installation and the installation stops. This occurs in...
View ArticleErrors communicating with my GPIB device in C++
I am trying to communicate with a GPIB device via a custom C++ program. I am using ni488-2.h and the associated obj file. When I send the commands to the device "manually" through the Measurement...
View ArticleTektronix AFG 3102 Error
Hello, What does this error mean?-410,"Query INTERRUPTED"I'm Using Tektronix AFG 3102 With GPIB and some VIs from the internet.It keeps popping up for no reason.I'm new to this so if you could explain...
View Articleread out name set in ni max of visa resource
I change the name of my visa resources in NI max and I want to actually save these names as group name in a tdms file I could find intf inst name thank you very much for your help regardsPascal
View ArticleIviSwtch Compliance Test IVI Specific Driver in CVI crashing
I have problem with IviSwtch Specific driver. I have finished all code for this driver and try to test in CVI tool called "Test IVI Specific Driver". Structure and Function panel test runs without any...
View ArticleRead parallel port
Hi Everyone, I am trying to read data from the parallel port with VISA. The basics: I'm using a PC running Windows 7, with LabVIEW 2010 (SP1). NI-MAX shows that I have NI-VISA 4.6. I have checked the...
View ArticleDriver du NI PXI-4065
Bonjour,j'ai besoin du driver du NI PXI-4065, je suis entrée sur la page du driver mais je ne l'ai pas trouvée, pourriez vous m'aider s'il vous plaît? Merci d'avance.
View ArticleIviCounter channel parameters meaning
Hi,I am looking for some example what meaning have "channels" in IviCounter class in the parameter of functions.It seems IviCounter class API only expect the instrument to have one counter channel...
View ArticleLack of IviDigitizer class driver in LabWindow/CVI
Hello, I try to create IVI Specific driver in LabWindow/CVI version 9.0.1 for digitizer but I don't see any of this types of instruments. I have installed newest IVI Compliance Package 4.6.1. There is...
View Article