VISA & Control Design Module Installation
Hi everyone; I have downloaded and installed LabView 2013 Student Edition and started to learn using it a little bit.I would like to try the Control Design and Simulation Module, and try to use VISA...
View ArticleCommunication with HP 3457A using HPIB with NI GPIB-USB-HS
Hello All, So what i am trying to do is get one of our HP 3457A DMM's to communication via the GPIB bus. This is an older piece of gear that is equipped with HPIB. I have had luck communicating with...
View Article[beginner] "Write to Measurement File" problem
H! :smileyhappy: I'm trying to read data sent from a DC motor, show on graph and save the necessary information to a text file. when I press the Run button, the code works as I want it to and I don't...
View Articlekjnml
So, if i want to have a knob to control V/div a how can i manage it; through vertical range and probe attenuation ;can you give me an example;and something elsealso the driver give in configure...
View Articlequestion about VI to control keithley 705
Hi I am using a Keithley 705 with a 7062 card. The reason to use this is to read two capacitances with only one capacitance bridge. Capacitance A is connected to Ch1 and Ch6, and Capacitance B is...
View ArticleHow to measure the Noise Figure(NF),IIP3,Stability using Agilent N5230A,PNA-L...
Dear Sir, I have designed the low noise amplifier, we have AGILENT NETWORK ANALYZER with N5230A PNA-L network analyzer. We don't have the user guide for the above said instrument. Can you...
View ArticleVS2012 C CNI4882, Need to update an exsiting VS2008 software interface
I have an software interface for a GPIB card running on a VS2008 C++ (MFC) environment with MeasurementStudio using the CNI4882 classNow we need to upgrade to VS2012. We have to stay on C++ and...
View ArticleHow to Connect Labview to a Modicon Quantum PLC (140 CPU 311 10) with Modbus
I was wondering if anybody could give some advice on how to connect Labview to a Modicon Quantum PLC ( the card is 140 CPU 311 10). I am wanting to use Labview as an HMI to control the PLC which is...
View ArticleHow to ensure received serial buffer completely read before stop
Hi, I have difficulties to ensure that all data in serial buffer are read before the program stop(after I push stop button). Help needed and appreciated. Thank you. rgds,Zahari
View ArticleXNET CAN CRC Error injection
Does the NI-XNET CAN support error injection in CRC ?Thank you,Radek
View ArticleRead timeout with USB-serial adapter
Hi everyone, sorry to post this kind of question again, but I've spent 2 days browsing this forum, the Mathworks forum, and several web pages, I still can't find the trick that will solve my problem...
View ArticleCalibration Executive with Fluke 5502A Calibrator
I have the following software/instruments:Windows XPCalibration Executive 3.5NI-DMM 3.1Fluke 5502A CalibratorA variety of NI DMMs What I want to do:Calibrate my NI DMMs using Calibration Executive and...
View ArticleCan't connect to keithley source meter through Agilent GPIB/USB interface...
Hi all, I am trying to use labview to control a keithley 2450 source meter. I have the source meter connected to my computer through an Agilent 82357b usb/gpib interface.The source meter shows up in...
View Articleserial jitter
Hello, I want to send serial data via RS485 port every 2ms on PXI 8433 board with 8106 controller. Baud rate: 2Mbit. I used timed loop with loop period is 2ms. I monitored loop time intervals with a...
View ArticleVISA-How to make real time graph in LabView 2013 from incoming data through...
I am new to LabView 2013. I made hardware for collecting data from deivce using serial port. My requirements are: I want to make real time graph of incoming data from hardware through serial port in...
View Article[visual studio c++] about input impedance
Hello, I've had a nice development session with NISCOPE C/C++ API, with Visual Studio 2012, last weeks.My NI device is a scope NI-5132, nice top 5Ms/s, 8bits,...
View Articlehow long it takes for a kistler 9255B to give an output for drilling a hole
how long it takes for a kistler 9255B dyno to give an output readings for cutting forces and moment when drilling a hole in a 10 mm plate .
View Article8431/16 RS422 C# programming (How to be sure all data is sent)
I am using the serial ports of 8431/16 card with C#. I am using "Write" function of "SerialPort class" in .NET. "Write" function is a blocking function so I assume that when "Write" function return all...
View ArticleEMtest GPIB interface error after updating NI-488.2 driver
I am using GPIB interface and Vendor Software to control EMtest devices (Autowave & VDS). After updating the NI-488.2 from version 2.2.7 (ni488227.exe) to 3.1.2 (ni488_312) the EMTest software is...
View Articlewhat is meaning this message ?
when i use exe file ....this message which is attached appearswhat is meaning this message
View Article