Software needed for Instrument Control
Hello, I currently have an Agilent Power Supply I want to control through LabVIEW. The power supply has a GPIB port and I have a GPIB to USB converter to hook this up to my computer's USB port. I have...
View ArticleVISA: (Hex 0xBFFF0015) Timeout expired before operation completed.
Hello,I am using an Agilent 6675A DC power supply and want to control this through LabVIEW. I have a GPIB to USB converter and have connected the supply to the computer through this cable. On opening...
View ArticleNI 9870 Problem with connection in VISA test panel
I am using NI 9870 for serial communication. It shows me following errors when trying to connect in VISA test panel. I have cross checked all the paramters like bata bits, parity, bytes and also...
View ArticleCommunication to NI 9202 without LabView
Hello Experts, I am a rookie in NI products and LabView. I will try my best to describe my question accurately. Our project uses "NI-9202" to measure and send data(including voltage and current...
View ArticleWhole Greens CBD : Oil Work For Pain Relief
In pregnant ladies, taking medicine ought to be done Whole Greens CBD under close supervision of the specialist. In the event that conceivable, the specialist will in general ask the patient not to...
View ArticleEcotech Serinus Gas Analyzer
Hello NI Community, I am currently trying to get an Ecotech Serinus gas analyzer to communicate in labVIEW. Specifically I just want to query the instrument for instantaneous gas data. I was...
View ArticleRead data bytes or wireless temperature sensor using Arduino in labview
Hi, I am using this code to monitor the data from Arduino connected to the wireless modem which receives the data from the wireless temperature sensor.Now I have shot circuit the RST pin and GND pin so...
View ArticleNI OPC S7 200
Hello, does anyone know if there is a communication protocol for Siemens S7 200 and NI OPC? Kind regards,Dominik Lastovčić
View ArticleIVI connection to TTI CPX200 power supply
I am trying to control a CPX200DP power supply from TTI over Ethernet LXI using the IVI driver supplied by the manufacturer. but when I try to make a new logical name I get the attached error message....
View ArticleGPIB with C# - 64\32 bit OS issues
We use some NI devices and we build a .NET application (C#) that needs to communicate with the devices through GPIB.The application have two versions one for windows 32 bit (XP) and one for 64 bit...
View ArticleStack Gas Analyzers
<a href="http://www.vasthi.com/stack-gas-analyzers/">stack gas analyzers</a> OMGA 8000 is one of the most powerful gas Analyzer and it works as The extractive dilution system extracts a...
View Articleflight control in QNET_VTOL_Workbook_Student
Excuse me can anyone help me about the value measured of steady-state error for the VTOL device step response when using PD controller in flight control experiment related to the...
View ArticleNI-Visa on ubuntu 18.04
hello,I try to install ni-visa on ubuntu 18.04 for using it with pyVisa library.I downloaded http://www.ni.com/download/ni-visa-17.0/6700/en/But it fail because ubuntu don't have rpm : sudo ./INSTALL...
View ArticleArduino: timeout error from Visa Serial write
I am using Arduino Mega 2560 to control 16 solenoid valves by ON/OFF 16 relays.The VI operate very well on my laptops (Samsung I5-7200U and Acer I3-2330M) but unstable on PCs (Core duo). After a few...
View ArticleVISA fails to connect even though I can talk in MAX
Hello, I'm having issues with communicating to my DC power supply over Ethernet connection. I can see it in MAX, and talk to it using the test panel, and have configured an alias. However, when I set...
View ArticleAdvantech Adam 4561 to 4019 not communicating
Having a problem communicating with an Adam 4019+ through an Adam 4561 USB to RS485 Converter. VISA seems to see the converter OK, but all it is just a converter to communicate with the 4019. I'm...
View ArticleRidiculous GPIB ibwrt error when communication with Handler~
I have already communicated with several Handler/Prober normally before.But I meet a ridiculous issue to communicate with a new handler today, and can't find how to solve it.the basic communication...
View Articlevisa resource name not shown in VI front panel
hello all I am trying to get data(or control ) from Agilent network analyzer (N5230C) using following hardware and softwares:hardware: Agilent 82357B GPIB-USB controller (cable)Agilent PNA series...
View ArticleListening to CAN Communication
I would like to use my program to collect and save data that is being transmitted via a CAN Bus. The CAN communication is between a motor controller and another software program. All I need my labview...
View ArticleCNC control using third party controller
Hi guys,I am a beginner to labview. I am trying to know, how to communicate with a third party controller of a three axis cnc machine using labview.For eg if i start from a normal communication like...
View Article