Subsequent delayed analog voltage generation with USB-X 6343 or 6353
Hello everyone, I need a delayed voltage signal or TTL after one immediately. To do so, I modified "Voltage - Finite Output" example vi following Dennis_Knutson advise in the 7th message here. You can...
View ArticleGPIB-ENET/1000 Command Reference
Hello, I would like to control GPIB instruments via Ethernet using my own softwarefom a Linux box. Not planning to use MAX and/or any other NI software/drivers.I need to be able to talk to the...
View ArticleTwo NI GPIB-USB-HS Can't Talk to Each Other
I have 3 instruments, 2 with NI GPIB-USB-HS adapters and 1 without. Both systems with adapters can see the 3rd instrument, but they can't see each other. I tried different boot orders, and several...
View ArticleTesto 350 toolbox 2012 (USB)
Hi, i am trying connect with a Testo 350 Maritime: http://www.testo350.com/350-maritime.html It uses a new toolbox bases on USB dll.It have several DLl´s, the most important are "testo3XXT.dll"...
View ArticleNI-DAQ Mx Base USB-6501 device names
Hello! We have a few USB-6501 devices hooked up to our RHEL 6.7 machine. It seems the auto-assignment of device names (dev1, dev2) is by serial number and when we change devices hooked up to the...
View ArticleNI MAX crashes on Devices expansion
Hello all, I'm trying to use NI MAX for another program and whenever I click to expand any option besides "IVI Drivers" the program crashes. The error report is shown below. I've tried repairing and...
View Articlehow to control esp 301 motion controller using labview with mouse?
I want to use mouse movement to control the ESP301 motor within labview code, I do not know how to deal the problem?The function should include: scroll control z axis motor, drag displacement control...
View ArticleShiftout with 32 bits long -ADF4351 registers
hello,I need to send 32 bits (5 times) to a PLL circuit (ADF4351)using PBP V2.x and a small PIC (lets say 12F675)As far as I understand Shitout command can deal with WORD not double word ..If I send...
View ArticleWhere are UART pins on sbRIO-9627?
I'm new to SingleBoard RIO and I need 5 UARTS but I can't find the RX TX pins. Where are the pins located? Datasheet: http://www.ni.com/pdf/manuals/375466a.pdfProduct page:...
View Article¿Cómo hago una palanca de 4 posiciones (arriba, abajo, izquiera, derecha) en...
Buenas noches, estoy iniciando en el tema de Labview, todavia soy un novato, tengo una duda, como realizo una palanca con las cuatro posiciones mencionadas en el titulo, y como hago una programación...
View ArticleNI-VIA to Send Digital Triggers?
Hi everyone,I have a question regarding the capabilities of NI-VISA, but first I would like to give you an overview of what the end goal is. I work in a Biomedical Engineering lab, and we do a lot of...
View ArticleSDI-12 communication with myRIO
I am trying to set up communication between water potential sensors using SDI-12 communication and myRIO 1900. Can I just short the TX and RX pins to connect the data wire to both pins or is there...
View ArticleProblem with camera image sometime turn balck
Hi,I'm using NI Vision Acquisition Software to control a Photon focus's camera (MV1-D2080 series). Everything working fine except that sometime when I snap an image, it come out black and when I grab...
View ArticleUSB-8452 OEM Connector Pitch
Does anyone know what the connector pitch is for the interface connector on the USB-8452 I2C/SPI module? I specificially need the OEM module connector specs but I believe that the standard version is...
View ArticleDriver Problem with PCI 232/16
I had a hard drive failure on a machine that communicates with several robots using RS232 and have the old PCI 232/16 186492B-01 board that I am trying to get to work. This isn't the newer PCI-8430/16....
View ArticleTerminating Resistor on NI PCIe-8433?
Hello, can anyone help me find the terminating resistor on the NI PCIe-8433 2-Port Isolated Serial Interface for PCI Express card? We are doing RS-485 communications and there should be a 120-ohm...
View Articlehow to control laser doppler vibrometer via ethernet
Dear membersi am trying for automation of my laser doppler vibrometer via high speed ethernet.company donot have any labview drivers but i have a general driver for remote conection. is there any...
View ArticleControlling Zeiss Axio Observer Z1m
Hi, I am trying to control Zeiss Axio Observer Z1m with the drivers I found in NI's driver network (here).I am using a usb-serial connector. My LabVIEW version is 2013. The connection is established,...
View Article.exe driver to labview
i am running a driver .exe for laser dopler vibrometer. i want to use it in lab viewor to convert it into labview driver because the manufacturer donot have any lab view drivercan any one please...
View ArticleError with NI 9871 (Serial RS485 interface)
Hello everybody. I am having troubles with serial comunication with this RS485 module. I checked in MAX and the ports are present in the system, but when I open the VISA test panel appears this error:...
View Article