Hexadecimal code for VISA-Temperature Controller
Greetings, First, I am not a programmer by any means so please excuse my ignorance. I'm trying to control an Accuthermo FTC100D temperature controller using LabVIEW 2013. I'd like to be able to send...
View ArticleClik here to view.
visa read
Dear all,I am using simple visa read function for reading the data from a device. The device is working as a master. Now to establish the communication i have to send the request frame to the device...
View Articletransmitter data by usb(serial port)
hii writting a program in ARM lpc1768 for A/D converterthen i use usb as serial port to send data to laptop an recieving by labviewmy sampling rate is 400Hzin labview i recieve data (i think) in ascii...
View ArticleI need a data sheet and a certificate of Volatility for GPIB-ENET, Ethernet...
I need to find the data sheet for 776933-21 GPIB-ENET Ethernet IEEE 488 Controller. I realize this is a end of life product but hoping one can be dug up somewhere. Thank you
View ArticleObsolete drivers for old hardware?
Hi folks. I'm looking for the driver package for Solaris 2.x for the PCI-MXI-2 board. I am trying to resurrect an old data acquisition system mainly for fun. I can't seem to find those old drivers...
View Articlebuffering recieve data from serial port
hii wrote a code for ARM lpc1768 (ADC) then tansfer data by serial port(9600 baud rate) then i recieve data correctly in labviewbut there is an issue that when i wanna plot it labview because of the...
View ArticleNeed Solaris drivers for old hardware
(Hi folks, I posted this question yesterday, but I really should have mentioned the platform in the subject line, as people will assume Windows. I didn't see a way to edit the subject of an existing...
View ArticleLeCroy Wavestation 2052 input lag from LabView
Hi All, We are trying to use the LeCroy Wavestation 2052 to set up a 2 channel frequency sweep for a new Mass Spectrometer. I have looked through the manual and SCPI commands for this model and...
View ArticleHP6633A to HP6633B conversion (Driver Needed)
We have sevral test stations running LabVIEW 2011 that contain a HP6633A power supply. Recently, we have not been able to get HP6633A from our vendor so someone purchased the HP6633B instead, thinking...
View ArticleDelay before sending a message via Visa Write
Hi everyone, I want to enable communication between a microcontroller (dsPIC33E) and the cRIO using RS-485 serial communication in the half-duplex mode. For that purpose, I use NI 9871 module. To see...
View ArticleDoes anyone know if labview can communicate with these zigbee receivers?
I have this zigbee kit: https://www.sparkfun.com/products/13197 and currently have a serial device connected to the transmitter end which is connected to an arduino that wirelessly sends a string value...
View ArticleLabVIEW with Keithley 6485 picoammeter and 2410 SMU
Hi all, I am having an issue with the "zchk" (zero check) on the front panel of the Keithley 6485 picoammeter-I need zchk to be turned off, and I can manually do this, but when I run the labview...
View ArticleProblem: Bulk Out(In) Pipe Status (Invalid Propery Value) Hex 0x3FFF0082
A USB Resource (Systec Xemo R262) is connected to the PXI 8135 controller and installed through the .inf FILE (by following the procedure as write here http://www.ni.com/tutorial/4478/de/) to use VISA...
View ArticleSpurious measurements on Agilent PXA N9030A Using LabVIEW
I am looking into Automating my Spurious Measurement, and I am looking at possibly buying LabVIEW. The equipment is Agilent PXA. Would someone familiar with LabVIEW tell me if the LabVIEW base...
View ArticleUnable to set frequency on HP 33120A
Hi all, First I appologize in advance if this is in the wrong location or if this is a stupid question. I am new to lab view. I am trying to work with an HP 33120A Arbitrary Waveform Generator. I have...
View ArticleClik here to view.
Does this cable perform the same function as this NI box?
http://sine.ni.com/nips/cds/view/p/lang/en/nid/14583 this is my niusb rs232/4 box, pretty sure it is broken, can I just replace it with this:...
View ArticleConnecting Keithley Sourcemeter 2400 with computer to measure Resistance
Hi guys, I have a keithley sourcemeter 2400. I want to connect it to my computer to measure resistance for each 5 min interval. I want the output of it to be saved in either .txt format or any other...
View ArticleClik here to view.
NI-Max with KUSB-488B Not Showing The GPIB Devices
I would like to describe the problem and steps made to try to fix the problem without success. I using Keithley KUSB-488B Device. We installed the latest version of the existing site...
View ArticleE364xa power supply screen is frozen when working in the remote mode.
I use the E364Xa sample VIs, which was downloaded with the driver (.dll) from NI website. The power supply screen freezes, when a sign "RMT" shows on the screen. Does anyone konow how to solve this...
View ArticlePopulate List on Amulet display
Gemstudio has a widget called "List" which is similar to a Multicolumn Listbox in Labview. It lets the user select one of the items from the list. Does anyone know how to programmatically populate a...
View Article